Grizzly G0647, G0646 Setup Safety, Items Needed for Setup, Unpacking, Description Qty

Page 16

SECTION 3: SETUP

Setup Safety

This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine!

Wear safety glasses dur- ing the entire setup pro- cess!

The Model G0646/G0647 is

aheavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment rated for at least 3500 lbs. to move the shipping crate and remove the machine from the crate.

Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use.

Items Needed for

Setup

The following items are needed to complete the setup process, but are not included with your machine:

Description		Qty
•	Assistants	At Least 2
•	Safety Glasses (for each person)	.............. 1

•Lifting Chain and Safety Hook

	(rated for at least 3500 lbs.)	....................... 1
•	Power Lifting Equipment
	(rated for at least 3500 lbs.)	....................... 1
•	Floor Mounting Hardware	As Needed

Unpacking

Your machine was carefully packaged for safe transportation. Remove the packaging materials from around your machine and inspect it. If you discover the machine is damaged, please imme- diately call Customer Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi- tion of your shipment, inventory the contents.

SUFFOCATION HAZARD!

Immediately discard all plas- tic bags and packing materi- als to eliminate choking/suf- focation hazards for children and animals.

-14-	G0646/G0647 50/65 Ton Ironworker

Image 16

Contents 50/65 TON Ironworker Page Table of Contents Foreword Functional Overview IntroductionContact Info Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Power Supply Circuit Requirements Power Connection DeviceCircuit Requirements 220/440V OperationTo rewire the Model G0646/G0647 for 440V operation 440V ConversionSetup Setup SafetyItems Needed for Setup UnpackingInventory Clean Up Inventory Figure QtyPlacement Location Site ConsiderationsMoving & Placing Base Unit Floor LoadMounting to Shop Floor Using Machine MountsBolting to Concrete Floors Test Run To test run the machineRecommended Adjustments Factory adjustments that should be verifiedOperations Operation SafetyBasic Controls Using the Punching Station Operation TipsPunching Motor Stop Button Turns the motor OFFTools Needed Qty Removing/Installing Punch ToolingTo remove punch tooling To install punch tooling Punch, adapter, retaining ring, Die installedBolster Mounting Hex Bolts 4 shown Removing & Installing Notch Dies Using the Notching StationNotching To install the notch dies Notch Die ClearancesPage Flat Stock Shearing To avoid tooling or workpiece breakageTo shear flat stock Bar Stock Shearing To shear bar stockAngle Iron Shearing Extension BarMaking a 90 Cut Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication H7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 Gal AccessoriesT20448T20452 T20501 T20456 H0736 Available Tooling Cleaning Protecting MaintenanceSchedule Lubrication Shearing Hold-Down Adjustment RodBeam Pivot Shaft Support Frame Lubrication Filling Hydraulic Reservoir Hydraulic SystemFluid Capacity Reservoir Draining & Re-Filling HydraulicTo drain and re-fill the hydraulic reservoir Beam Alignment To align the beamTroubleshooting ServiceMotor & Electrical Operations Flat Stock Shearing Dies To remove and replace the flat stock shearing diesAngle Iron Shearing Dies To remove the angle iron shearing diesBar Stock Shearing Dies To remove and replace the bar stock shearing diesDisconnect Machine from Power Shearing Table Alignment Limit Rings To reset the position of the limit ringsHydraulic Fluid Pressure Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Electrical Components Wiring Diagram Limit switch wiringMotor Wiring Diagram Motor wiring G0646/G0647 50/65 Ton IronworkerHydraulic System Overview Parts G0646 Upper Front-Half Parts List DescriptionG0647 Upper Front-Half Parts List Upper HalfG0646 Upper Rear-Half Parts List G0647 Upper Rear-Half Parts List DescriptionCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns