Grizzly G0647 Site Considerations, Moving & Placing Base Unit, Floor Load, Placement Location

Page 18

Site Considerations

Floor Load

Refer to the Machine Data Sheets (beginning on Page 4) for the weight and footprint specifications of your machine. Some floors may require addi- tional reinforcement to support both the machine and operator.

Placement Location

Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your new machine. See Figures 10–11for the minimum working clearances.

��

��

Figure 10. Model G0646 minimum working

clearances.

��

��

Figure 11. Model G0647 minimum working

clearances.

-16-

Moving & Placing

Base Unit

The Model G0646/G0647 is

aheavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment rated for at least 3500 lbs. to move the shipping crate and remove the machine from the crate.

To move the machine:

1.Remove the crating and plastic wrap, then unbolt the machine from the shipping pallet.

2.Attach the safety hook and lifting chain to the lifting eye bolt (see Figure 12).

Eye Bolt

Figure 12. Safety hook and lifting chain attached

to the eye bolt of the machine.

3.With assistance to steady the machine, care- fully lift it enough to clear the pallet and floor obstacles, then move it to the prepared loca- tion.

G0646/G0647 50/65 Ton Ironworker

Image 18

Contents 50/65 TON Ironworker Page Table of Contents Introduction Foreword Functional OverviewContact Info Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Circuit Requirements Power Supply Circuit RequirementsPower Connection Device 220/440V OperationTo rewire the Model G0646/G0647 for 440V operation 440V ConversionItems Needed for Setup SetupSetup Safety UnpackingInventory Clean Up Inventory Figure QtyMoving & Placing Base Unit Placement LocationSite Considerations Floor LoadUsing Machine Mounts Mounting to Shop FloorBolting to Concrete Floors Test Run To test run the machineRecommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsBasic Controls Punching Using the Punching StationOperation Tips Motor Stop Button Turns the motor OFFRemoving/Installing Punch Tooling Tools Needed QtyTo remove punch tooling To install punch tooling Punch, adapter, retaining ring, Die installedBolster Mounting Hex Bolts 4 shown Using the Notching Station Removing & Installing Notch DiesNotching To install the notch dies Notch Die ClearancesPage Flat Stock Shearing To avoid tooling or workpiece breakageTo shear flat stock Bar Stock Shearing To shear bar stockExtension Bar Angle Iron ShearingMaking a 90 Cut Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication Accessories H7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 GalT20448T20452 T20501 T20456 H0736 Available Tooling Maintenance Cleaning ProtectingSchedule Shearing Hold-Down Adjustment Rod LubricationBeam Pivot Shaft Support Frame Lubrication Hydraulic System Filling Hydraulic ReservoirFluid Capacity Draining & Re-Filling Hydraulic ReservoirTo drain and re-fill the hydraulic reservoir Beam Alignment To align the beamService TroubleshootingMotor & Electrical Operations Flat Stock Shearing Dies To remove and replace the flat stock shearing diesAngle Iron Shearing Dies To remove the angle iron shearing diesBar Stock Shearing Dies To remove and replace the bar stock shearing diesDisconnect Machine from Power Shearing Table Alignment To reset the position of the limit rings Limit RingsHydraulic Fluid Pressure Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Electrical Components Wiring Diagram Limit switch wiringMotor Wiring Diagram Motor wiring G0646/G0647 50/65 Ton IronworkerHydraulic System Overview Parts G0646 Upper Front-Half Parts List DescriptionG0647 Upper Front-Half Parts List Upper HalfG0646 Upper Rear-Half Parts List G0647 Upper Rear-Half Parts List DescriptionCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns