Grizzly G0646, G0647 owner manual Extension Bar & Tools

Page 71

extension bar

Extension Bar & Tools

		��
			��
��	��			��
��
					��
					��
		��
					��
			��		��
					��
					��
			��
		��		��
		��		��
			��	��
			��
		��
		��

��

��

��

��

��

��

��

��

REF	PART #	DESCRIPTION

215	P0646215	GUIDE BAR
216	P0646216	SCALE 1M
217	P0646217	MOUNTING BRACKET
218	PSB70M	CAP SCREW M10-1.5 X 45
219	PLW06M	LOCK WASHER 10MM
220	P0646220	END CAP
221	PSB17M	CAP SCREW M4-.7 X 10
222	P0646222	PIVOT CLAMP
223	P0646223	LOCK LEVER M12-1.75 X 40
224	P0646224	LOCK LEVER M16-2 X 45
225	P0646225	EXTENSION BAR
226	PSB83M	CAP SCREW M6-1 X 55
227	PW03M	FLAT WASHER 6MM
228	PN01M	HEX NUT M6-1

REF	PART #	DESCRIPTION

229	P0646229	CLAMP
230	PSB169M	CAP SCREW M12-1.75 X 75
231	PW06M	FLAT WASHER 12MM
232	P0646232	SUPPORT SHAFT
233	P0646233	SENSOR MOUNT END CAP
241	P0646241	SPANNER WRENCH
244	P0646244	HEX WRENCH KIT 2.5-10MM
245	PAW12M	HEX WRENCH 12MM
246	PAW14M	HEX WRENCH 14MM
247	PAW17M	HEX WRENCH 17MM
248	P0646248	ADJUSTABLE WRENCH
249	P0646249	GREASE GUN
250	P0646250	TOOL BOX

G0646/G0647 50/65 Ton Ironworker

-69-

Image 71

Contents 50/65 TON Ironworker Page Table of Contents Contact Info IntroductionForeword Functional Overview Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics 220/440V Operation Power Supply Circuit RequirementsPower Connection Device Circuit Requirements440V Conversion To rewire the Model G0646/G0647 for 440V operationUnpacking SetupSetup Safety Items Needed for SetupInventory Figure Qty Inventory Clean UpFloor Load Placement LocationSite Considerations Moving & Placing Base UnitBolting to Concrete Floors Using Machine MountsMounting to Shop Floor To test run the machine Test RunFactory adjustments that should be verified Recommended AdjustmentsBasic Controls Operation SafetyOperations Motor Stop Button Turns the motor OFF Using the Punching StationOperation Tips PunchingTo remove punch tooling Removing/Installing Punch ToolingTools Needed Qty Punch, adapter, retaining ring, Die installed To install punch toolingBolster Mounting Hex Bolts 4 shown Notching Using the Notching StationRemoving & Installing Notch Dies Notch Die Clearances To install the notch diesPage To avoid tooling or workpiece breakage Flat Stock ShearingTo shear flat stock To shear bar stock Bar Stock ShearingMaking a 90 Cut Extension BarAngle Iron Shearing Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication T20448T20452 T20501 T20456 H0736 AccessoriesH7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 Gal Available Tooling Schedule MaintenanceCleaning Protecting Beam Pivot Shaft Shearing Hold-Down Adjustment RodLubrication Support Frame Lubrication Fluid Capacity Hydraulic SystemFilling Hydraulic Reservoir To drain and re-fill the hydraulic reservoir Draining & Re-Filling HydraulicReservoir To align the beam Beam AlignmentMotor & Electrical ServiceTroubleshooting Operations To remove and replace the flat stock shearing dies Flat Stock Shearing DiesTo remove the angle iron shearing dies Angle Iron Shearing DiesTo remove and replace the bar stock shearing dies Bar Stock Shearing DiesDisconnect Machine from Power Shearing Table Alignment Hydraulic Fluid Pressure To reset the position of the limit ringsLimit Rings Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Limit switch wiring Electrical Components Wiring DiagramMotor wiring G0646/G0647 50/65 Ton Ironworker Motor Wiring DiagramHydraulic System Overview Parts Description G0646 Upper Front-Half Parts ListG0647 Upper Front-Half Parts List Half UpperG0646 Upper Rear-Half Parts List Description G0647 Upper Rear-Half Parts ListCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns