Grizzly G0646, G0647 owner manual Notching Station

Page 69

Notching Station

���

���

��� ���

���

���

���

���

���

���

���

���

���

REF

PART #

DESCRIPTION

 

 

 

137

P0646137

NOTCH PUNCH

138

P0646138

CAP SCREW M20-2.5 X 90

139

P0646139

NOTCH SIDE DIE

140

P0646140

NOTCH END DIE

141

P0646141

NOTCH BOLSTER

142

PSB64M

CAP SCREW M10-1.5 X 25

143

PSS21M

SET SCREW M8-1.25 X 25

REF

PART #

DESCRIPTION

 

 

 

144

P0646144

NOTCH BOLSTER CLAMP

145

PLW05M

LOCK WASHER 12MM

146

PW06M

FLAT WASHER 12MM

147

PB12M

HEX BOLT M12-1.75 X 55

148

PSB64M

CAP SCREW M10-1.5 X 25

149

P0646149

TEE NUT M12-1.75

G0646/G0647 50/65 Ton Ironworker

-67-

Image 69
Contents 50/65 TON Ironworker Page Table of Contents Introduction Foreword Functional OverviewContact Info Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Power Connection Device Power Supply Circuit RequirementsCircuit Requirements 220/440V Operation440V Conversion To rewire the Model G0646/G0647 for 440V operationSetup Safety SetupItems Needed for Setup UnpackingInventory Figure Qty Inventory Clean UpSite Considerations Placement LocationMoving & Placing Base Unit Floor LoadUsing Machine Mounts Mounting to Shop FloorBolting to Concrete Floors To test run the machine Test RunFactory adjustments that should be verified Recommended AdjustmentsOperation Safety OperationsBasic Controls Operation Tips Using the Punching StationPunching Motor Stop Button Turns the motor OFFRemoving/Installing Punch Tooling Tools Needed QtyTo remove punch tooling Punch, adapter, retaining ring, Die installed To install punch toolingBolster Mounting Hex Bolts 4 shown Using the Notching Station Removing & Installing Notch DiesNotching Notch Die Clearances To install the notch diesPage To avoid tooling or workpiece breakage Flat Stock ShearingTo shear flat stock To shear bar stock Bar Stock ShearingExtension Bar Angle Iron ShearingMaking a 90 Cut Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication Accessories H7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 GalT20448T20452 T20501 T20456 H0736 Available Tooling Maintenance Cleaning ProtectingSchedule Shearing Hold-Down Adjustment Rod LubricationBeam Pivot Shaft Support Frame Lubrication Hydraulic System Filling Hydraulic ReservoirFluid Capacity Draining & Re-Filling Hydraulic ReservoirTo drain and re-fill the hydraulic reservoir To align the beam Beam AlignmentService TroubleshootingMotor & Electrical Operations To remove and replace the flat stock shearing dies Flat Stock Shearing DiesTo remove the angle iron shearing dies Angle Iron Shearing DiesTo remove and replace the bar stock shearing dies Bar Stock Shearing DiesDisconnect Machine from Power Shearing Table Alignment To reset the position of the limit rings Limit RingsHydraulic Fluid Pressure Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Limit switch wiring Electrical Components Wiring DiagramMotor wiring G0646/G0647 50/65 Ton Ironworker Motor Wiring DiagramHydraulic System Overview Parts Description G0646 Upper Front-Half Parts ListG0647 Upper Front-Half Parts List Half UpperG0646 Upper Rear-Half Parts List Description G0647 Upper Rear-Half Parts ListCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns