Grizzly G0647, G0646 owner manual Label Placement

Page 72

Label Placement

	��	��	��
	��			��


				��
	��			��
				��
��				��
				��

��

			��
			��
			��
��			��
			��
��
	��		��
	��	��	��
			��

REF	PART #	DESCRIPTION

301	P0646301	CLAMP WARNING LABEL VERT.
302	P0646302	MACHINE ID LABEL (G0646)
302	P0647302	MACHINE ID LABEL (G0647)
303	PLABEL-12B	READ MANUAL LABEL HORZ.
304	P0646304	SAFE OPERATION NOTICE LABEL
305	P0646305	CLAMP WARNING LABEL HORZ.
306	P0646306	EYE/FACE HAZARD LABEL HORZ.
307	P0646307	DISCONNECT POWER LABEL HORZ.
308	P0646308	SHOCK HAZARD LABEL HORZ.
309	PLABEL-14	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

310	P0646310	TONNAGE LABEL (G0646)
310	P0647310	TONNAGE LABEL (G0647)
311	P0646311	MODEL NUMBER LABEL (G0646)
311	P0647311	MODEL NUMBER LABEL (G0647)
312	PLABEL-34	PREWIRED 220V LABEL
313	P0646313	ORANGE TOUCH UP PAINT
314	PPAINT-11	GRIZZLY PUTTY TOUCH UP PAINT
315	PPAINT-1	GRIZZLY GREEN TOUCH UP PAINT
316	G8588	GRIZZLY OVAL NAMEPLATE

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-70-	G0646/G0647 50/65 Ton Ironworker

Image 72

Contents 50/65 TON Ironworker Page Table of Contents Introduction Foreword Functional OverviewContact Info Identification G0646 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker G0647 Machine Data Sheet G0646/G0647 50/65 Ton Ironworker Safety Instructions for Machinery G0646/G0647 50/65 Ton Ironworker Additional Safety Instructions for Ironworkers Additional Safety Instructions for Hydraulics Power Supply Circuit Requirements Power Connection DeviceCircuit Requirements 220/440V OperationTo rewire the Model G0646/G0647 for 440V operation 440V ConversionSetup Setup SafetyItems Needed for Setup UnpackingInventory Clean Up Inventory Figure QtyPlacement Location Site ConsiderationsMoving & Placing Base Unit Floor LoadUsing Machine Mounts Mounting to Shop FloorBolting to Concrete Floors Test Run To test run the machineRecommended Adjustments Factory adjustments that should be verifiedOperation Safety OperationsBasic Controls Using the Punching Station Operation TipsPunching Motor Stop Button Turns the motor OFFRemoving/Installing Punch Tooling Tools Needed QtyTo remove punch tooling To install punch tooling Punch, adapter, retaining ring, Die installedBolster Mounting Hex Bolts 4 shown Using the Notching Station Removing & Installing Notch DiesNotching To install the notch dies Notch Die ClearancesPage Flat Stock Shearing To avoid tooling or workpiece breakageTo shear flat stock Bar Stock Shearing To shear bar stockExtension Bar Angle Iron ShearingMaking a 90 Cut Making a Less Than 90 Cut Adjusting Stroke Length Beam Lubrication Accessories H7379-Tapmatic#1 Gold 16 oz H7380-Tapmatic#1 Gold 1 GalT20448T20452 T20501 T20456 H0736 Available Tooling Maintenance Cleaning ProtectingSchedule Shearing Hold-Down Adjustment Rod LubricationBeam Pivot Shaft Support Frame Lubrication Hydraulic System Filling Hydraulic ReservoirFluid Capacity Draining & Re-Filling Hydraulic ReservoirTo drain and re-fill the hydraulic reservoir Beam Alignment To align the beamService TroubleshootingMotor & Electrical Operations Flat Stock Shearing Dies To remove and replace the flat stock shearing diesAngle Iron Shearing Dies To remove the angle iron shearing diesBar Stock Shearing Dies To remove and replace the bar stock shearing diesDisconnect Machine from Power Shearing Table Alignment To reset the position of the limit rings Limit RingsHydraulic Fluid Pressure Electrical Panel Wiring Control Panel Wiring Electrical Panel Wiring Diagram Control Panel Wiring Diagram Electrical Components Wiring Diagram Limit switch wiringMotor Wiring Diagram Motor wiring G0646/G0647 50/65 Ton IronworkerHydraulic System Overview Parts G0646 Upper Front-Half Parts List DescriptionG0647 Upper Front-Half Parts List Upper HalfG0646 Upper Rear-Half Parts List G0647 Upper Rear-Half Parts List DescriptionCabinet G0646 Cabinet G0647 Cabinet Notching Station Punching Station Extension Bar & Tools Label Placement Page Page Warranty and Returns