Bard I60H1D, I42H1D, I36H1D, I48H1D, I30H1D installation instructions Electrical Specifications

TABLE 2

ELECTRICAL SPECIFICATIONS

				Single Circuit						Dual Circuit
	Rated	No. Field	Minimum	Maximum	Field		Minimum		Maximum		Field		Ground
Model	Volts, Hertz	Power				Ground	Circuit		External Fuse		Power
			Circuit	External Fuse	Power								Wire
	and Phase	Circuits				Wire	Ampacity		or Ckt. Breaker		Wire Size
			Ampacity	or Ckt. Brkr.	Wire Size
							Ckt. A	Ckt. B	Ckt. A	Ckt. B	Ckt. A	Ckt. B	Ckt. A	Ckt. B
I30H1-A0Z		1	22	35	8	10
A05	230/208-1	1	48	50	8	10
A10		1 or 2	74	80	4	8	48	30	50	30	8	10	10	10
I30H1-B0Z		1	17	25	10	10
B06	230/208-3	1	35	35	8	10
B09		1	44	45	8	10
I30H1-C0Z		1	9	10	14	14
C06	460-3	1	18	20	12	12
C09		1	22	25	10	10
I36H1-A0Z		1	26	40	8	10
A05	230/208-1	1	52	60	6	10
A10		1 or 2	78	80	4	8	26	52	40	60	8	6	10	10
1 A15		1 or 2	84	90	4	8	26	52	40	60	8	6	10	10
I36H1-B0Z		1	22	30	10	10
B06	230/208-3	1	40	45	8	10
B09		1	49	50	8	10
1 B15		1	51	60	6	10
I36H1-C0Z		1	11	15	14	14
C06	460-3	1	20	20	12	12
C09		1	24	25	10	10
1 C15		1	28	30	10	10
I42H1-A0Z		1	30	45	8	10
A05	230/208-1	1	56	60	6	10
A10		1 or 2	82	90	4	8	56	26	60	30	6	10	10	10
1 A15		1 or 2	82	90	4	8	56	52	60	60	6	6	10	10
I42H1-B0Z		1	25	35	8	10
B06	230/208-3	1	43	50	8	10
B09		1	52	60	6	10
1 B15		1	52	60	6	10
I42H1-C0Z		1	12	15	14	14
C06	460-3	1	21	25	10	10
C09		1	26	30	10	10
1 C15		1	28	30	10	10
I48H1-A0Z		1	34	50	8	10
A04		1	54	60	6	10
A05	230/208-1	1 or 2	59	70	6	8	35	26	45	30	8	10	10	10
A10		1 or 2	85	90	3	8	35	52	45	60	8	6	10	10
1 A15		1 or 2	85	90	3	8	35	52	45	60	8	6	10	10
1 A20		1 or 2	110	110	2	6	59	52	60	60	6	6	10	10
I48H1-B0Z		1	26	35	8	10
B06		1	44	50	8	10
B09	230/208-3	1	53	60	6	10
1 B15		1	53	60	6	10
1 B18		1	53	60	6	10
I48H1-C0Z		1	15	20	12	12
C06		1	25	30	10	10
C09	460-3	1	29	30	10	10
1 C15		1	29	30	10	10
1 C18		1	29	30	10	10
I60H1-A0Z		1	44	60	8	10
A05		1 or 2	70	80	4	8	44	26	60	30	8	10	10	10
A10	230/208-1	1 or 2	96	100	3	8	44	52	60	60	8	6	10	10
1 A15		1 or 2	96	100	3	8	44	52	60	60	8	6	10	10
1 A20		1 or 2	112	120	2	6	60	52	60	60	6	6	10	10
I60H1-B0Z		1	31	45	8	10
B06		1	49	60	8	10
B09	230/208-3	1	58	60	6	10
1 B15		1	58	60	6	10
1 B18		1 or 2	63	70	6	8	31	54	45	60	8	6	10	10
I60H1-C0Z		1	15	20	12	12
C06		1	25	30	10	10
C09	460-3	1	29	30	10	10
1 C15		1	29	30	10	10
1 C18		1	29	30	10	10

These “Minimum Circuit Ampacity” values are to be used for sizing the field power conductors. Refer to the National Electric Code (latest revision), article 310 for power conductor sizing.

Caution: When more than one field power conductor circuit is run through one conduit, the conductors must be derated. Pay special attention to note 8 of table 310 regarding Ampacity Adjustment Factors when more than three conductors are in a raceway.

Maximum size of the time delay fuse or HACR type circuit breaker for protection of field wiring conductors. Based on 75°C copper wire. All wiring must conform to the National Electrical Code and all local codes. Maximum KW that can operate with heat pump on is 10KW for 1-Phase and 9KW for 3-Phase.

1Represents Electric Heat Only. Electrical Control Circuit will lockout Heat Pump Operation.

Manual	2100-549G
Page	6 of 59