Woodstock W1773, W1772 owner manual Dust Collection, Power Connection, Recommended CFM at Sander

Page 21

W1772/W1773 37" Drum Sander

Dust Collection

Recommended CFM at Sander:

1600 CFM

Do not confuse this CFM recommendation with the rating of the dust collector. To determine the CFM at the dust port, you must take into account many variables, includ- ing the CFM rating of the dust collector, the length of hose between the dust collector and the machine, the amount of branches or Y's, and the amount of other open lines throughout the system. Explaining this calculation is beyond the scope of this manual. If you are unsure of your system, consult an expert or purchase a good dust collection "how-to" book.

We recommend using a dust collection system that pro- duces a minimum of 2000 CFM. A fine layer of dust will be present on your stock as it comes out of the sander. This is normal.

To connect the dust ports to a dust collector, do these steps:

1.Attach 4" dust collection hoses to the dust ports shown in Figure 17 and secure them with hose clamps.

Figure 17. Dust port locations.

SET UP

Power Connection

Before connecting to power, read through the ELECTRICAL section on Page 11 to check that your setup follows the safety and circuit requirements for this machine. Be sure to also have your electrician on hand for the "Test Run" in case the power is connected out of phase (Model W1773 only).

To connect the sander to the power source, do these steps:

1.Remove the screws securing the control panel and lift off the face plate.

Attempting to connect this machine to the power source without a qualified electrician greatly increases the risk of electrocution, fire, or machine damage.

-19-

Image 21

Contents Drum Sander Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Single-Phase Operation W1772 Electrical SpecificationsElectrical W1773 220V/440V Phase Operation Phase ConverterW1773 Electrical Specifications To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 toItems Needed for Setup SetupUnpacking InventoryIf you do not hear any scraping sounds go to Step AssemblyControl panel mounting bolts W1772/W1773 minimum working clearances Machine PlacementLifting Sander Mounting to Shop FloorTo place the sander in a permanent location, do these steps To connect the sander to the power source, do these steps Power ConnectionDust Collection Recommended CFM at SanderTo check the gear oil, do these steps Gear Oil CheckTo test run the drum sander, do these steps Test RunSET Recommended AdjustmentsControl Panel OperationsGeneral Sanding Drums Start Button Starts the sanding drumsDepth of Cut To adjust the conveyor speed, do these stepsVariable Speed To set the depth of cut, do these stepsUsing the Amp Draw Meter SandingTo sand a workpiece, do these steps Sanding Tips Grit Class Choosing SandpaperTo change the paper, do these steps Paper ReplacementDrum Sander Accessories Maintenance CleaningLubrication Lubricating gear box StepService Gauge BlocksTo make the gauge blocks, do these steps To adjust V-belt tension, do these steps Belt ServiceTo align the pulleys, do these steps Bearing ReplacementPages 38 That no obstructions prevent bearing lubricationTo tension the conveyor, do these steps Conveyor Tensioning TrackingTo track the conveyor, do these steps TrackingAdjusting Drums Perpendicular to Feed Direction Drum AdjustmentsLoosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locationsAdjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knobPressure Roller Height Pressure roller adjustment NutsScale Pointer Calibration To adjust a dust scoop, do these stepsDust Scoops Table Lift ScewsMarking sprocket tooth Chain To adjust the table lift screws, do these stepsEmergency stop bar limit Switch W1772/W1773 Wiring OverviewW1772/W1773 Control Panel W1772/W1773 control panel wiringW1772 electrical box W1772 Electrical Box 220V, 1-PhFigures W1772 Electrical Box Wiring 220V, 1-PhW1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitorsW1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-PhaseW1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-PhaseFigures 66 W1773 Electrical Box Wiring 440V, 3-PhaseW1773 Sanding Drum Motor W1773 220V sanding drum motor WiringW1773 Feed Motor W1773 220V feed motor wiringMoving parts have come to a complete stop TroubleshootingMachine Operations Frame Parts Breakdown PartsPART# Description Frame Parts ListParts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts BreakdownMicro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts ListLabel Placement Comments Warranty RegistrationBOX BELLINGHAM, WA Warranty