Woodstock W1772, W1773 owner manual Gear Oil Check, To check the gear oil, do these steps

Page 22

W1772/W1773 37" Drum Sander

SET UP

2.Feed the power wires through the strain relief on the bottom of the control panel, tighten the strain relief, connect the cord to the terminals shown in Figure 18 or 19, and reinstall the control panel face plate.

Note (Model W1773 Only): When using a phase con- verter, connect the manufactured power leg to the L1 terminal (Figure 19). The L1 terminal can handle power fluctuation because it is wired directly to the motor. The other wires connect to the controls and must be consistent to prevent damage.

3.SHUT OFF THE MAIN POWER AT THE POWER SOURCE CIRCUIT BREAKER and attach the wires to the locking shutoff switch.

Gear Oil Check

It is important to make sure the gear box has adequate oil in it before running the sander for the first time, to ensure the gears do not burn up.

To check the gear oil, do these steps:

1.Remove the shipping seal from the side of the vent- ed fill plug (Figure 20), if not already done so.

2.Check the sight glass shown on the back of the gear box to make sure gear oil is present.

3.If the gearbox oil level is low, follow the steps on Page 30 to refill the oil.

Strain

Relief

Ground

Figure 18. W1772 control panel wiring.

Strain

Relief

Ground

Figure 19. W1773 control panel wiring.

	Sight Glass
Shipping Seal
Inserted in
Vented Fill Plug	Gear Box

Figure 20. Typical vented fill plug (sight

glass not shown).

-20-

Image 22

Contents Drum Sander Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Electrical Specifications W1772 Single-Phase OperationElectrical Phase Converter W1773 220V/440V Phase OperationW1773 Electrical Specifications Rewiring W1773 to To rewire the Model W1773 for 440V operation, do these stepsUnpacking SetupItems Needed for Setup InventoryAssembly If you do not hear any scraping sounds go to StepControl panel mounting bolts Machine Placement W1772/W1773 minimum working clearancesMounting to Shop Floor Lifting SanderTo place the sander in a permanent location, do these steps Dust Collection Power ConnectionTo connect the sander to the power source, do these steps Recommended CFM at SanderGear Oil Check To check the gear oil, do these stepsTest Run To test run the drum sander, do these stepsRecommended Adjustments SETGeneral OperationsControl Panel Sanding Drums Start Button Starts the sanding drumsVariable Speed To adjust the conveyor speed, do these stepsDepth of Cut To set the depth of cut, do these stepsSanding Using the Amp Draw MeterTo sand a workpiece, do these steps Sanding Tips Choosing Sandpaper Grit ClassPaper Replacement To change the paper, do these stepsDrum Sander Accessories Cleaning MaintenanceLubrication Step Lubricating gear boxGauge Blocks ServiceTo make the gauge blocks, do these steps Belt Service To adjust V-belt tension, do these stepsBearing Replacement To align the pulleys, do these stepsThat no obstructions prevent bearing lubrication Pages 38Conveyor Tensioning Tracking To tension the conveyor, do these stepsTracking To track the conveyor, do these stepsDrum Adjustments Adjusting Drums Perpendicular to Feed DirectionFront and rear drum Adjustment locations Loosen the front drum pillow bearing lock nuts FigureAdjusting Drum Height & Drum-to-Conveyor Parallelism Rear right sanding drum micro Adjusting knob Loosen the front drum pillow bearing lock nuts ,Pressure roller adjustment Nuts Pressure Roller HeightDust Scoops To adjust a dust scoop, do these stepsScale Pointer Calibration Table Lift ScewsTo adjust the table lift screws, do these steps Marking sprocket tooth ChainW1772/W1773 Wiring Overview Emergency stop bar limit SwitchW1772/W1773 control panel wiring W1772/W1773 Control PanelW1772 Electrical Box 220V, 1-Ph W1772 electrical boxW1772 Electrical Box Wiring 220V, 1-Ph FiguresW1772 sanding drum motor Wiring and start capacitors W1772 Sanding & Feed MotorsW1773 Electrical Box 220V, 3-Phase W1773 Electrical Box Wiring 220V, 3-Phase FiguresW1773 Electrical Box 440V, 3-Phase W1773 440V 3-phase electrical box wiringW1773 Electrical Box Wiring 440V, 3-Phase Figures 66W1773 220V sanding drum motor Wiring W1773 Sanding Drum MotorW1773 220V feed motor wiring W1773 Feed MotorTroubleshooting Moving parts have come to a complete stopMachine Operations Parts Frame Parts BreakdownFrame Parts List PART# DescriptionParts Breakdown Conveyor Parts List Roller & Drum Parts Breakdown XPK55MMicro-Adjustment Breakdown Electrical Components Electrical Parts List CurrentsensorLabel Placement Warranty Registration CommentsBOX BELLINGHAM, WA Warranty