Woodstock W1772, W1773 owner manual Unpacking, Items Needed for Setup, Inventory

Page 16

W1772/W1773 37" Drum Sander

SETUP

SET UP

Unpacking

This machine has been carefully packaged for safe trans- portation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately.

Items Needed for Setup

The following items are needed to complete the set up process, but are not included with your machine:

Description		Qty
• Safety Glasses (for each person)		1
• Power Lifting Equipment (forklift)		1
• Lifting Straps (min. 2000 lb capacity)		2
•	An Assistant	1
• Power Cord (length as needed)		1
•	Power Disconnect Box	1
•	Dust Collection System	1
• Dust Hoses 4" (length as needed)		4
•	Hose Clamp 4"	4

Inventory

The following is a description of the main components shipped with the Model W1772/W1773. Lay the compo- nents out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the pack- aging materials carefully. Occasionally we pre-install cer- tain components for safer shipping.

Box Inventory (Figure 6)		Qty
A.	Drum Sander	1
B.	Control Panel	1
C.	Handwheel	1
D.	Top Cover	1
Tools (Not Shown)
	—Hex Wrenches 4, 5mm	1 Ea
	—Wrenches 12/14	1
	—Phillips Head Screwdriver	1
	—Spring Tension Tools	2
	—Paper Retaining Clips	2
	—Rubber Plates (Dust Scoop)	2

SUFFOCATION HAZARD!

Immediately discard all

plastic bags and pack-

ing materials to elimi-

nate choking/suffocation hazards for children and animals.

OFF

Disconnect power to the machine before you do any assembly or adjust- ment tasks! Otherwise, serious per- sonal injury to you or others may occur!

A

B

D

C

Figure 6. W1772/W1773 inventory.

-14-

Image 16

Contents Drum Sander Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Electrical Specifications W1772 Single-Phase Operation Electrical Phase Converter W1773 220V/440V Phase OperationW1773 Electrical Specifications Rewiring W1773 to To rewire the Model W1773 for 440V operation, do these stepsSetup Items Needed for SetupUnpacking InventoryAssembly If you do not hear any scraping sounds go to StepControl panel mounting bolts Machine Placement W1772/W1773 minimum working clearancesMounting to Shop Floor Lifting SanderTo place the sander in a permanent location, do these steps Power Connection To connect the sander to the power source, do these stepsDust Collection Recommended CFM at SanderGear Oil Check To check the gear oil, do these stepsTest Run To test run the drum sander, do these stepsRecommended Adjustments SETOperations Control PanelGeneral Sanding Drums Start Button Starts the sanding drumsTo adjust the conveyor speed, do these steps Depth of CutVariable Speed To set the depth of cut, do these stepsSanding Using the Amp Draw MeterTo sand a workpiece, do these steps Sanding Tips Choosing Sandpaper Grit ClassPaper Replacement To change the paper, do these stepsDrum Sander Accessories Cleaning MaintenanceLubrication Step Lubricating gear boxGauge Blocks ServiceTo make the gauge blocks, do these steps Belt Service To adjust V-belt tension, do these stepsBearing Replacement To align the pulleys, do these stepsThat no obstructions prevent bearing lubrication Pages 38Conveyor Tensioning Tracking To tension the conveyor, do these stepsTracking To track the conveyor, do these stepsDrum Adjustments Adjusting Drums Perpendicular to Feed DirectionFront and rear drum Adjustment locations Loosen the front drum pillow bearing lock nuts FigureAdjusting Drum Height & Drum-to-Conveyor Parallelism Rear right sanding drum micro Adjusting knob Loosen the front drum pillow bearing lock nuts ,Pressure roller adjustment Nuts Pressure Roller HeightTo adjust a dust scoop, do these steps Scale Pointer CalibrationDust Scoops Table Lift ScewsTo adjust the table lift screws, do these steps Marking sprocket tooth ChainW1772/W1773 Wiring Overview Emergency stop bar limit SwitchW1772/W1773 control panel wiring W1772/W1773 Control PanelW1772 Electrical Box 220V, 1-Ph W1772 electrical boxW1772 Electrical Box Wiring 220V, 1-Ph FiguresW1772 sanding drum motor Wiring and start capacitors W1772 Sanding & Feed MotorsW1773 Electrical Box 220V, 3-Phase W1773 Electrical Box Wiring 220V, 3-Phase FiguresW1773 Electrical Box 440V, 3-Phase W1773 440V 3-phase electrical box wiringW1773 Electrical Box Wiring 440V, 3-Phase Figures 66W1773 220V sanding drum motor Wiring W1773 Sanding Drum MotorW1773 220V feed motor wiring W1773 Feed MotorTroubleshooting Moving parts have come to a complete stopMachine Operations Parts Frame Parts BreakdownFrame Parts List PART# DescriptionParts Breakdown Conveyor Parts List Roller & Drum Parts Breakdown XPK55MMicro-Adjustment Breakdown Electrical Components Electrical Parts List CurrentsensorLabel Placement Warranty Registration CommentsBOX BELLINGHAM, WA Warranty