Woodstock W1772, W1773 owner manual Label Placement

Page 68

W1772/W1773 37" Drum Sander

Label Placement

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www. shopfoxtools.com to order new labels.

620	610 (Rear View)	606

607

600	601	602	603	604	605

619

618

608

617	620

616

615

614

609

	613	610
	612-1	610
	612-1
	612	611

PARTS

REF	PART�#	DESCRIPTION
600	XLABEL-11	SAFETY�GLASSES�LABEL
601	X1772601	DISCONNECT�POWER�LABEL
602	X1772602	FEED�ONLY�ONE�LABEL
603	X1772603	HAND�PINCH�IN�BELT�LABEL
604	X1772604	KEEP�DOOR�CLOSED
605	XLABEL-12	READ�MANUAL�LABEL
606	X1772606	MACHINE�ID�LABEL�(W1772)
606	X1773606	MACHINE�ID�LABEL�(W1773)
607	X1772607	AMP�LOAD�LABEL�(W1772)
607	X1773607	AMP�LOAD�LABEL�(W1773)
608	X1772608	CONTROL�PANEL�PLATE�LABEL
609	X1772609	DON'T�CHANGE�SPEEDS�LABEL
610	X1772610	HAND�WARNING

REF	PART�#	DESCRIPTION
611	X1772611	W1772�MODEL�NUMBER�LABEL
611	X1773611	W1773�MODEL�NUMBER�LABEL
612	X1772612	SHOP�FOX�LOGO�PLATE
612-1	X1772612-1	LOGO�SCREW
613	X1772613	DECORATIVE�STRIPE�TAPE
614	X1772614	DECORATIVE�STRIPE�TAPE
615	XPPAINT-1	SHOP�FOX�WHITE�PAINT
616	XPPAINT-11	SHOP�FOX�SAFETY�RED
617	X1772617	LABEL�EMERGENCY�STOP
618	X1772618	BELT�TENSION�ADJUST�LEFT�LABEL
619	X1772619	BELT�TENSION�ADJUST�RIGHT�LABEL
620	X1772620	MICRO-ADJUST�KNOB�LABEL

-66-

Image 68

Contents Drum Sander Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders Electrical W1772 Single-Phase OperationW1772 Electrical Specifications W1773 Electrical Specifications W1773 220V/440V Phase OperationPhase Converter Rewiring W1773 to To rewire the Model W1773 for 440V operation, do these stepsSetup Items Needed for SetupUnpacking InventoryAssembly If you do not hear any scraping sounds go to StepControl panel mounting bolts Machine Placement W1772/W1773 minimum working clearancesTo place the sander in a permanent location, do these steps Lifting SanderMounting to Shop Floor Power Connection To connect the sander to the power source, do these stepsDust Collection Recommended CFM at SanderGear Oil Check To check the gear oil, do these stepsTest Run To test run the drum sander, do these stepsRecommended Adjustments SETOperations Control PanelGeneral Sanding Drums Start Button Starts the sanding drumsTo adjust the conveyor speed, do these steps Depth of CutVariable Speed To set the depth of cut, do these stepsTo sand a workpiece, do these steps Using the Amp Draw MeterSanding Sanding Tips Choosing Sandpaper Grit ClassPaper Replacement To change the paper, do these stepsDrum Sander Accessories Lubrication MaintenanceCleaning Step Lubricating gear boxTo make the gauge blocks, do these steps ServiceGauge Blocks Belt Service To adjust V-belt tension, do these stepsBearing Replacement To align the pulleys, do these stepsThat no obstructions prevent bearing lubrication Pages 38Conveyor Tensioning Tracking To tension the conveyor, do these stepsTracking To track the conveyor, do these stepsDrum Adjustments Adjusting Drums Perpendicular to Feed DirectionFront and rear drum Adjustment locations Loosen the front drum pillow bearing lock nuts FigureAdjusting Drum Height & Drum-to-Conveyor Parallelism Rear right sanding drum micro Adjusting knob Loosen the front drum pillow bearing lock nuts ,Pressure roller adjustment Nuts Pressure Roller HeightTo adjust a dust scoop, do these steps Scale Pointer CalibrationDust Scoops Table Lift ScewsTo adjust the table lift screws, do these steps Marking sprocket tooth ChainW1772/W1773 Wiring Overview Emergency stop bar limit SwitchW1772/W1773 control panel wiring W1772/W1773 Control PanelW1772 Electrical Box 220V, 1-Ph W1772 electrical boxW1772 Electrical Box Wiring 220V, 1-Ph FiguresW1772 sanding drum motor Wiring and start capacitors W1772 Sanding & Feed MotorsW1773 Electrical Box 220V, 3-Phase W1773 Electrical Box Wiring 220V, 3-Phase FiguresW1773 Electrical Box 440V, 3-Phase W1773 440V 3-phase electrical box wiringW1773 Electrical Box Wiring 440V, 3-Phase Figures 66W1773 220V sanding drum motor Wiring W1773 Sanding Drum MotorW1773 220V feed motor wiring W1773 Feed MotorTroubleshooting Moving parts have come to a complete stopMachine Operations Parts Frame Parts BreakdownFrame Parts List PART# DescriptionParts Breakdown Conveyor Parts List Roller & Drum Parts Breakdown XPK55MMicro-Adjustment Breakdown Electrical Components Electrical Parts List CurrentsensorLabel Placement Warranty Registration CommentsBOX BELLINGHAM, WA Warranty