Woodstock W1773, W1772 owner manual Assembly, If you do not hear any scraping sounds go to Step

Page 17

W1772/W1773 37" Drum Sander

Assembly

To attach the top cover, control panel, and handwheel to the drum sander, do these steps:

1.Remove the six button head cap screws from the top cover shown in Figure 7, and remove the two lock knobs shown in Figure 8.

2.Place the top cover on the sander and attach the hinges with the screws removed in Step 1.

Note: To close the top cover fully, tuck the gas struts under the cover.

3.While an assistant holds the top cover up, install each strut on a bracket with a jam nut, as shown in Figure 9. The threaded end of each strut should be flush with the outside of the bracket.

4.Close the top cover, remove the cap screws securing the pulley cover, and open the cover.

5.Pull the V-belt down to rotate the sanding drums, and listen for any scraping sounds.

—If the sanding drums scrape the plastic dust scoop or metal dust scoop plates on the top cover, refer to instructions on Page 43 for adjusting the dust scoops.

—If you do not hear any scraping sounds go to Step 6.

6.Reinstall the pulley cover with the cap screws removed in Step 4, and reinstall the knobs removed in Step 1, to secure the top cover.

Figure 7. Removing cap screws on top

cover.

Hinges

SET UP

Lock Knobs

Figure 8. Lock knobs and hinges.

Gas Strut	Jam Nut
	Jam Nut
	Bracket

Figure 9. Gas strut installed (right side

shown).

-15-

Image 17

Contents Drum Sander Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders Electrical W1772 Single-Phase OperationW1772 Electrical Specifications W1773 Electrical Specifications W1773 220V/440V Phase OperationPhase Converter To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 toItems Needed for Setup SetupUnpacking InventoryIf you do not hear any scraping sounds go to Step AssemblyControl panel mounting bolts W1772/W1773 minimum working clearances Machine PlacementTo place the sander in a permanent location, do these steps Lifting SanderMounting to Shop Floor To connect the sander to the power source, do these steps Power ConnectionDust Collection Recommended CFM at SanderTo check the gear oil, do these steps Gear Oil CheckTo test run the drum sander, do these steps Test RunSET Recommended AdjustmentsControl Panel OperationsGeneral Sanding Drums Start Button Starts the sanding drumsDepth of Cut To adjust the conveyor speed, do these stepsVariable Speed To set the depth of cut, do these stepsTo sand a workpiece, do these steps Using the Amp Draw MeterSanding Sanding Tips Grit Class Choosing SandpaperTo change the paper, do these steps Paper ReplacementDrum Sander Accessories Lubrication MaintenanceCleaning Lubricating gear box StepTo make the gauge blocks, do these steps ServiceGauge Blocks To adjust V-belt tension, do these steps Belt ServiceTo align the pulleys, do these steps Bearing ReplacementPages 38 That no obstructions prevent bearing lubricationTo tension the conveyor, do these steps Conveyor Tensioning TrackingTo track the conveyor, do these steps TrackingAdjusting Drums Perpendicular to Feed Direction Drum AdjustmentsLoosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locationsAdjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knobPressure Roller Height Pressure roller adjustment NutsScale Pointer Calibration To adjust a dust scoop, do these stepsDust Scoops Table Lift ScewsMarking sprocket tooth Chain To adjust the table lift screws, do these stepsEmergency stop bar limit Switch W1772/W1773 Wiring OverviewW1772/W1773 Control Panel W1772/W1773 control panel wiringW1772 electrical box W1772 Electrical Box 220V, 1-PhFigures W1772 Electrical Box Wiring 220V, 1-PhW1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitorsW1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-PhaseW1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-PhaseFigures 66 W1773 Electrical Box Wiring 440V, 3-PhaseW1773 Sanding Drum Motor W1773 220V sanding drum motor WiringW1773 Feed Motor W1773 220V feed motor wiringMoving parts have come to a complete stop TroubleshootingMachine Operations Frame Parts Breakdown PartsPART# Description Frame Parts ListParts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts BreakdownMicro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts ListLabel Placement Comments Warranty RegistrationBOX BELLINGHAM, WA Warranty