Woodstock W1772 W1773 Electrical Box 440V, 3-Phase, W1773 440V 3-phase electrical box wiring

Page 54

W1772/W1773 37" Drum Sander

W1773 Electrical Box 440V, 3-Phase

OFF				Sanding
				Motor		Sanding Motor
		Amp Meter		Motor		Sanding Motor
		Amp Meter		Contactor		Relay		Feed Motor
		Transformer		Contactor		Relay		Feed Motor
		Transformer				(dial @ 21.5A)		Contactor
						(dial @ 21.5A)		Contactor

Main Panel

av

Current

Sansor

Feed Motor

Relay

(dial @ 0.65A)

Incoming

Power

Terminal

Block

Control Panel

Terminal Block

Figure 76. W1773 440V 3-phase electrical box wiring.

SERVICE

-52-

Image 54

Contents Drum Sander Page Contents Introduction Woodstock Technical SupportIntroduction Introduction Introduction Introduction Controls and Features Safety Standard Safety InstructionsAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Single-Phase Operation W1772 Electrical SpecificationsElectrical W1773 220V/440V Phase Operation Phase ConverterW1773 Electrical Specifications Rewiring W1773 to To rewire the Model W1773 for 440V operation, do these stepsUnpacking SetupItems Needed for Setup InventoryAssembly If you do not hear any scraping sounds go to StepControl panel mounting bolts Machine Placement W1772/W1773 minimum working clearancesLifting Sander Mounting to Shop FloorTo place the sander in a permanent location, do these steps Dust Collection Power ConnectionTo connect the sander to the power source, do these steps Recommended CFM at SanderGear Oil Check To check the gear oil, do these stepsTest Run To test run the drum sander, do these stepsRecommended Adjustments SETGeneral OperationsControl Panel Sanding Drums Start Button Starts the sanding drumsVariable Speed To adjust the conveyor speed, do these stepsDepth of Cut To set the depth of cut, do these stepsUsing the Amp Draw Meter SandingTo sand a workpiece, do these steps Sanding Tips Choosing Sandpaper Grit ClassPaper Replacement To change the paper, do these stepsDrum Sander Accessories Maintenance CleaningLubrication Step Lubricating gear boxService Gauge BlocksTo make the gauge blocks, do these steps Belt Service To adjust V-belt tension, do these stepsBearing Replacement To align the pulleys, do these stepsThat no obstructions prevent bearing lubrication Pages 38Conveyor Tensioning Tracking To tension the conveyor, do these stepsTracking To track the conveyor, do these stepsDrum Adjustments Adjusting Drums Perpendicular to Feed DirectionFront and rear drum Adjustment locations Loosen the front drum pillow bearing lock nuts FigureAdjusting Drum Height & Drum-to-Conveyor Parallelism Rear right sanding drum micro Adjusting knob Loosen the front drum pillow bearing lock nuts ,Pressure roller adjustment Nuts Pressure Roller HeightDust Scoops To adjust a dust scoop, do these stepsScale Pointer Calibration Table Lift ScewsTo adjust the table lift screws, do these steps Marking sprocket tooth ChainW1772/W1773 Wiring Overview Emergency stop bar limit SwitchW1772/W1773 control panel wiring W1772/W1773 Control PanelW1772 Electrical Box 220V, 1-Ph W1772 electrical boxW1772 Electrical Box Wiring 220V, 1-Ph FiguresW1772 sanding drum motor Wiring and start capacitors W1772 Sanding & Feed MotorsW1773 Electrical Box 220V, 3-Phase W1773 Electrical Box Wiring 220V, 3-Phase FiguresW1773 Electrical Box 440V, 3-Phase W1773 440V 3-phase electrical box wiringW1773 Electrical Box Wiring 440V, 3-Phase Figures 66W1773 220V sanding drum motor Wiring W1773 Sanding Drum MotorW1773 220V feed motor wiring W1773 Feed MotorTroubleshooting Moving parts have come to a complete stopMachine Operations Parts Frame Parts BreakdownFrame Parts List PART# DescriptionParts Breakdown Conveyor Parts List Roller & Drum Parts Breakdown XPK55MMicro-Adjustment Breakdown Electrical Components Electrical Parts List CurrentsensorLabel Placement Warranty Registration CommentsBOX BELLINGHAM, WA Warranty