Woodstock W1772 owner manual W1773 Feed Motor, W1773 220V feed motor wiring

Page 57

W1772/W1773 37" Drum Sander

W1773 Feed Motor

Figure 79. W1773 220V feed motor wiring.

��

��

��

��

��

��

��

� �	�
�	�
�	�
�
�	�

��

��

��

Figure 80. W1773 440 feed drum motor wiring.

��

��

��

��

��

��

�	� �
�		�
		�
�		�
�		�
�
	�	�
	�

��

��

��

��

��

W1773 220 3-Ph, Page 51 or

W1773 440V 3-Ph, Page 53

-55-

SERVICE

Image 57

Contents Drum Sander Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Single-Phase Operation W1772 Electrical SpecificationsElectrical W1773 220V/440V Phase Operation Phase ConverterW1773 Electrical Specifications To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 toItems Needed for Setup SetupUnpacking InventoryIf you do not hear any scraping sounds go to Step AssemblyControl panel mounting bolts W1772/W1773 minimum working clearances Machine PlacementLifting Sander Mounting to Shop FloorTo place the sander in a permanent location, do these steps To connect the sander to the power source, do these steps Power ConnectionDust Collection Recommended CFM at SanderTo check the gear oil, do these steps Gear Oil CheckTo test run the drum sander, do these steps Test RunSET Recommended AdjustmentsControl Panel OperationsGeneral Sanding Drums Start Button Starts the sanding drumsDepth of Cut To adjust the conveyor speed, do these stepsVariable Speed To set the depth of cut, do these stepsUsing the Amp Draw Meter SandingTo sand a workpiece, do these steps Sanding Tips Grit Class Choosing SandpaperTo change the paper, do these steps Paper ReplacementDrum Sander Accessories Maintenance CleaningLubrication Lubricating gear box StepService Gauge BlocksTo make the gauge blocks, do these steps To adjust V-belt tension, do these steps Belt ServiceTo align the pulleys, do these steps Bearing ReplacementPages 38 That no obstructions prevent bearing lubricationTo tension the conveyor, do these steps Conveyor Tensioning TrackingTo track the conveyor, do these steps TrackingAdjusting Drums Perpendicular to Feed Direction Drum AdjustmentsLoosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locationsAdjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knobPressure Roller Height Pressure roller adjustment NutsScale Pointer Calibration To adjust a dust scoop, do these stepsDust Scoops Table Lift ScewsMarking sprocket tooth Chain To adjust the table lift screws, do these stepsEmergency stop bar limit Switch W1772/W1773 Wiring OverviewW1772/W1773 Control Panel W1772/W1773 control panel wiringW1772 electrical box W1772 Electrical Box 220V, 1-PhFigures W1772 Electrical Box Wiring 220V, 1-PhW1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitorsW1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-PhaseW1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-PhaseFigures 66 W1773 Electrical Box Wiring 440V, 3-PhaseW1773 Sanding Drum Motor W1773 220V sanding drum motor WiringW1773 Feed Motor W1773 220V feed motor wiringMoving parts have come to a complete stop TroubleshootingMachine Operations Frame Parts Breakdown PartsPART# Description Frame Parts ListParts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts BreakdownMicro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts ListLabel Placement Comments Warranty RegistrationBOX BELLINGHAM, WA Warranty