Woodstock owner manual Machine Placement, W1772/W1773 minimum working clearances

Page 19

W1772/W1773 37" Drum Sander

Machine Placement

•Floor Load: This machine distributes a heavy load in a small footprint. Some residential floors may require additional bracing to support both machine and operator.

•Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your drum sander (see Figure 13 for minimum working clearances).

•Lighting: Lighting should be bright enough to eliminate shadow and prevent eye strain.

•Electrical: Electrical circuits must be dedicated or large enough to handle amperage requirements. Follow local electrical codes for proper installation of new lighting, outlets, or circuits.

MAKE your shop “child safe.” Ensure that your workplace is inaccessible to youngsters by closing and locking all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjust- ing or operating equipment.

The Model W1772/W1773 is an extremely heavy machine. Serious per- sonal injury may occur if safe moving methods are not followed. To be safe, you will need assistance and power equipment when moving the ship- ping crate and removing the machine from the crate.

Use lifting straps with a combined minimum of 2000 lbs. lifting capacity. If lifting straps break, serious personal injury may occur.

SET UP

��

��

Figure 13. W1772/W1773 minimum working clearances.

-17-

Image 19

Contents Drum Sander Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Electrical Specifications W1772 Single-Phase OperationElectrical Phase Converter W1773 220V/440V Phase OperationW1773 Electrical Specifications To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 toInventory SetupItems Needed for Setup UnpackingIf you do not hear any scraping sounds go to Step AssemblyControl panel mounting bolts W1772/W1773 minimum working clearances Machine PlacementMounting to Shop Floor Lifting SanderTo place the sander in a permanent location, do these steps Recommended CFM at Sander Power ConnectionTo connect the sander to the power source, do these steps Dust CollectionTo check the gear oil, do these steps Gear Oil CheckTo test run the drum sander, do these steps Test RunSET Recommended AdjustmentsSanding Drums Start Button Starts the sanding drums OperationsControl Panel GeneralTo set the depth of cut, do these steps To adjust the conveyor speed, do these stepsDepth of Cut Variable SpeedSanding Using the Amp Draw MeterTo sand a workpiece, do these steps Sanding Tips Grit Class Choosing SandpaperTo change the paper, do these steps Paper ReplacementDrum Sander Accessories Cleaning MaintenanceLubrication Lubricating gear box StepGauge Blocks ServiceTo make the gauge blocks, do these steps To adjust V-belt tension, do these steps Belt ServiceTo align the pulleys, do these steps Bearing ReplacementPages 38 That no obstructions prevent bearing lubricationTo tension the conveyor, do these steps Conveyor Tensioning TrackingTo track the conveyor, do these steps TrackingAdjusting Drums Perpendicular to Feed Direction Drum AdjustmentsLoosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locationsAdjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knobPressure Roller Height Pressure roller adjustment NutsTable Lift Scews To adjust a dust scoop, do these stepsScale Pointer Calibration Dust ScoopsMarking sprocket tooth Chain To adjust the table lift screws, do these stepsEmergency stop bar limit Switch W1772/W1773 Wiring OverviewW1772/W1773 Control Panel W1772/W1773 control panel wiringW1772 electrical box W1772 Electrical Box 220V, 1-PhFigures W1772 Electrical Box Wiring 220V, 1-PhW1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitorsW1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-PhaseW1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-PhaseFigures 66 W1773 Electrical Box Wiring 440V, 3-PhaseW1773 Sanding Drum Motor W1773 220V sanding drum motor WiringW1773 Feed Motor W1773 220V feed motor wiringMoving parts have come to a complete stop TroubleshootingMachine Operations Frame Parts Breakdown PartsPART# Description Frame Parts ListParts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts BreakdownMicro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts ListLabel Placement Comments Warranty RegistrationBOX BELLINGHAM, WA Warranty