Woodstock W1773, W1772 owner manual Operations, Control Panel, General

Page 25

W1772/W1773 37" Drum Sander

OPERATIONS

Control Panel

Below is a summary of your sander control panel and the components that it controls. Use the list with Figure 23 to become familiar with your sander.

A.Sanding Drums Start Button: Starts the sanding drums.

B.Conveyor Start Button: Starts the conveyor belt.

C.Amp Draw Meter: Indicates the combined amperage draw of both motors, to help control the load so as not to damage the motor.

D.Emergency Stop Button: Stops all electrical power to motors in event of emergency.

E.Conveyor Stop Button: Stops the conveyor belt.

F.Sanding Drums Stop Button: Stops the sanding drums.

General

The Model W1772/W1773 will perform many types of oper- ations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly.

The instructions in this section are written with the under- standing that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine!

If you are an inexperienced operator, we strongly recom- mend that you read books, trade articles, or seek training from an experienced Drum Sander operator before per- forming any unfamiliar operations. Above all, your safety should come first!

-23-

	B
A	C
A

F	D
	E

Figure 23. Control panel interface.

OFF

DO NOT investigate problems or adjust the machine while it is running. Wait until the machine is turned OFF, unplugged and all working parts have come to a complete stop before proceeding!

Always wear safety glasses and a respirator when operating this machine. Failure to comply may result in serious personal injury, allergic reactions, or respiratory problems.

OPERATIONS

Image 25

Contents Drum Sander Page Contents Woodstock Technical Support IntroductionIntroduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Electrical Specifications W1772 Single-Phase OperationElectrical Phase Converter W1773 220V/440V Phase OperationW1773 Electrical Specifications To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 toItems Needed for Setup SetupUnpacking InventoryIf you do not hear any scraping sounds go to Step AssemblyControl panel mounting bolts W1772/W1773 minimum working clearances Machine PlacementMounting to Shop Floor Lifting SanderTo place the sander in a permanent location, do these steps To connect the sander to the power source, do these steps Power ConnectionDust Collection Recommended CFM at SanderTo check the gear oil, do these steps Gear Oil CheckTo test run the drum sander, do these steps Test RunSET Recommended AdjustmentsControl Panel OperationsGeneral Sanding Drums Start Button Starts the sanding drumsDepth of Cut To adjust the conveyor speed, do these stepsVariable Speed To set the depth of cut, do these stepsSanding Using the Amp Draw MeterTo sand a workpiece, do these steps Sanding Tips Grit Class Choosing SandpaperTo change the paper, do these steps Paper ReplacementDrum Sander Accessories Cleaning MaintenanceLubrication Lubricating gear box StepGauge Blocks ServiceTo make the gauge blocks, do these steps To adjust V-belt tension, do these steps Belt ServiceTo align the pulleys, do these steps Bearing ReplacementPages 38 That no obstructions prevent bearing lubricationTo tension the conveyor, do these steps Conveyor Tensioning TrackingTo track the conveyor, do these steps TrackingAdjusting Drums Perpendicular to Feed Direction Drum AdjustmentsLoosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locationsAdjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knobPressure Roller Height Pressure roller adjustment NutsScale Pointer Calibration To adjust a dust scoop, do these stepsDust Scoops Table Lift ScewsMarking sprocket tooth Chain To adjust the table lift screws, do these stepsEmergency stop bar limit Switch W1772/W1773 Wiring OverviewW1772/W1773 Control Panel W1772/W1773 control panel wiringW1772 electrical box W1772 Electrical Box 220V, 1-PhFigures W1772 Electrical Box Wiring 220V, 1-PhW1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitorsW1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-PhaseW1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-PhaseFigures 66 W1773 Electrical Box Wiring 440V, 3-PhaseW1773 Sanding Drum Motor W1773 220V sanding drum motor WiringW1773 Feed Motor W1773 220V feed motor wiringMoving parts have come to a complete stop TroubleshootingMachine Operations Frame Parts Breakdown PartsPART# Description Frame Parts ListParts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts BreakdownMicro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts ListLabel Placement Comments Warranty RegistrationBOX BELLINGHAM, WA Warranty