Omega Engineering 185-210 DUS Engine OIL and Filter, Engine Cooling Specifications, Mixtures

Page 15

4.2 ENGINE OIL AND FILTER

See engine manufactures operator/instruction manual for the proper engine oil and filter changing intervals for the brand engine in your Boss compressor.

OIL FILTER REPLACEMENT

1.Clean the area around the lubricating filter head.

2.Remove the filter.

3.Clean the o-ring surface of the filter head.

NOTE: The o-ring can stick on the filter head. Make sure it is removed.

4.Apply a light film of lubricating oil to the o-ring-sealing surface before installing.

5.Install the filter as specified by the filter manufacturer.

CAUTION

MECHANICAL OVER-TIGHTENING MAY DISTORT THE THREADS OR DAMAGE THE FILTER ELEMENT SEAL.

4.3 ENGINE COOLING SPECIFICATIONS

Diesel engines require a balanced coolant mixture of water and ethylene glycol base antifreeze. This protects the engine cooling system from corrosions as well as freezing damage. The Boss compressor is shipped from the factory with a 50/50 mixture of water and ethylene glycol. In tropical climates where freeze protection is not required, glycol engine coolant should still be used. It will help prevent corrosion and pitting of cylinder liners. See engine manufactures operator/instruction manual for the proper engine coolant for the brand engine in your Boss compressor.

MIXTURES:

Antifreeze concentration level should not exceed recommended levels. Doing so can cause cooling system failure.

·Use a high quality, low silicate antifreeze

·A mixture of 50% antifreeze and 50% water is required for temperatures above –37 º C (-34 ºF).

·A mixture of 60% antifreeze and 40% water us required for environments below –37 ºC (-34 ºF). This provides protection to –54 ºC (-65 ºF).

·Never exceed a 60% antifreeze and 40% water mix.

ENGINE COOLING SYSTEM

All engines have a pressurized cooling system that contains a 50/50 mixture of water and ethylene glycol. Daily maintenance of the system includes a check of the coolant level, proper belt adjustment of fan and water pump drives, soundness of fan and cleanliness of the radiator and oil cooler to permit airflow. Further cooling system maintenance is defined in the engine maintenance manual.

16

P/N: 307271

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Serial Number Model Number 06/17/2008 MCM Omega ToolPage Table of Contents Page OWNER’S Responsibility IntroductionAIR Compressor Safety Precautions Tampering with Noise Control System Prohibited User ModificationCompressor USE and Compressed AIR SafetyParking Before Starting the CompressorLifting ServicingDescription IntroductionRotary Compressor Components Engine Components Frame ChassisEnclosure Instrument Panel DoorOperation Starting ProcedureEmergency Shutdown Procedure Routine Shutdown Procedure15 P/N MaintenanceEngine Fuel Specifications Cold Weather FuelMixtures Engine Cooling SpecificationsOIL Filter Replacement Engine OIL and FilterCoolant Level Radiator Pressure CAPRadiator Compressor OILCompressor OIL Specifications 19 P/N Compressor OIL FilterCompressor & Engine AIR Filter Maintenance Element ReplacementElement Inspection Compressor OIL Thermostatic Valve Belts & Belt AdjustmentCleaning Oilthermostat Separator Element ReplacementCONTROLS-OPERATION and Adjustments AdjustmentIdle Speed Adjustment Procedures Instruments BatteryPressure Regulator Adjustment Rated Speed AdjustmentDaily Operation Maintenance Schedule25 P/N Maintenance Schedule ChartCompressor AIR Filter Element Procedure for Ordering PartsTroubleshooting Troubleshooting27 P/N Symptom Cause Remedy Troubleshooting Chart29 P/N Clean or replace the element Warranty Boss INDUSTRIES, INC Genesis Drive LAPORTE,31 P/N Summary of Main Warranty Provisions 33 P/N WARRANTY/RETURN Goods InstructionsWarranty Claims Preparation of Part Return Return or Warranty Claims Filing ProceduresDamage in Transit General35 P/N Screw Compressor AIR-END Exchange ProgramPage 37 P/N Section Assembly DrawingsCoolers & PARTS, Omega 185-210 DUS Frame & PARTS, Omega 185-210 DUSEngine & PARTS, Omega 185-210 DUS Compressor & PARTS, Omega 185-210 DUSREV Description Date ENG Revision History 39 P/NSENDER, Coolant Temperature 3/8 BRACKET,ASSY ENG. AIR CleanerSWITCH, Press 18# N.O /8MNPT SWITCH, Temp 220 F NC Gold Contacts41 P/N 307271 RELIEF, 1/2 NPT 175 PSI CONNECTOR, 1 Mjic X 1 MnptCONNECTOR, Male 1/4 T X 1/4 D CONNECTOR, 1/4 Mnpt X 1/4 Tube 200PSI DEGVALVE, Service 1 X 3/4-Y Vented BRACKET, Battery Hold DownBOLT, Battery Hold Down BATTERY, 12VOLT 650CCA aLA PORTE, 45 P/NWASHER, Flat Wide 1/4 SS PANEL, DUS Rear AccessPANEL, DUS OIL Fill Access Latch ADJ Lever C2-33-3547 P/N John Deere 4045 DF Engine
Top Page Image Contents