Omega Engineering 185-210 DUS, JD 4045 manual General, Damage in Transit

Page 33

GENERAL

An approved claim depends on the following provision:

1.An RGA # must be issued by BOSS INDUSTRIES. (See filing procedures.)

2.Failed part must be returned within 30 days of original invoice date, freight prepaid, with RGA #.

3.Part is determined to be defective.

4.Workmanship is determined to be defective.

5.Machine is within warranty period.

6.Machine has been operated within design conditions.

Claims made through distributors must be verified by distributor prior to contacting BOSS INDUSTRIES.

DAMAGE IN TRANSIT

Do not return damaged merchandise to BOSS INDUSTRIES, please follow claim procedure.

1. Loss in transit:

The merchandise in our kit or provided in our factory installations has been thoroughly inspected or carefully installed and tested before leaving our plant. However, regardless of the care taken at the factory, there is a possibility that damage may occur in shipment. For this reason, it is recommended that the unit be carefully inspected for evidence of possible damage or malfunction during the first few hours of operation. Responsibility for the safe delivery of the kit or factory installed unit was assumed by the carrier at the time of shipment. Therefore, claims for loss or damage to the contents of the kit or factory installed unit should be made upon the carrier.

2.Concealed loss or damage:

Concealed loss or damage means loss or damage, which does not become apparent until the kit is unpacked or the factory-installed unit is run by the end-user. The contents of the kit or factory installed unit may be damaged due to rough handling while in route to its destination, even thought the kit or factory installed unit shows no external damage. When the damage is discovered upon unpacking, make a written request for inspection by the carrier agent within fifteen days of delivery date. Then file a claim with the carrier since such damage is the carrier’s responsibility.

By following these instructions carefully, we guarantee our full support of your claims, to protect you against loss from concealed damage.

3.Visible Loss or Damage

Any external evidence of loss or damage must be noted on the Freight Bill or Express Receipt, and signed by the carrier’s agent. Failure to adequately describe such external evidence of loss, or damage may result in the carrier refusing to honor a damage claim. The carrier will supply the form required to file such a claim.

34

P/N: 307271

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Serial Number Model Number 06/17/2008 MCM Omega ToolPage Table of Contents Page OWNER’S Responsibility IntroductionAIR Compressor Safety Precautions Tampering with Noise Control System Prohibited User ModificationParking SafetyBefore Starting the Compressor Compressor USE and Compressed AIRLifting ServicingDescription IntroductionRotary Compressor Components Engine Components Enclosure ChassisInstrument Panel Door FrameEmergency Shutdown Procedure Starting ProcedureRoutine Shutdown Procedure OperationEngine Fuel Specifications MaintenanceCold Weather Fuel 15 P/NOIL Filter Replacement Engine Cooling SpecificationsEngine OIL and Filter MixturesRadiator Radiator Pressure CAPCompressor OIL Coolant LevelCompressor OIL Specifications 19 P/N Compressor OIL FilterCompressor & Engine AIR Filter Maintenance Element ReplacementElement Inspection Cleaning Oilthermostat Belts & Belt AdjustmentSeparator Element Replacement Compressor OIL Thermostatic ValveCONTROLS-OPERATION and Adjustments AdjustmentIdle Speed Adjustment Procedures Pressure Regulator Adjustment BatteryRated Speed Adjustment InstrumentsDaily Operation Maintenance Schedule25 P/N Maintenance Schedule ChartCompressor AIR Filter Element Procedure for Ordering PartsTroubleshooting Troubleshooting27 P/N Symptom Cause Remedy Troubleshooting Chart29 P/N Clean or replace the element Warranty Boss INDUSTRIES, INC Genesis Drive LAPORTE,31 P/N Summary of Main Warranty Provisions Warranty Claims Preparation of Part Return WARRANTY/RETURN Goods InstructionsReturn or Warranty Claims Filing Procedures 33 P/NDamage in Transit General35 P/N Screw Compressor AIR-END Exchange ProgramPage 37 P/N Section Assembly DrawingsEngine & PARTS, Omega 185-210 DUS Frame & PARTS, Omega 185-210 DUSCompressor & PARTS, Omega 185-210 DUS Coolers & PARTS, Omega 185-210 DUSREV Description Date ENG Revision History 39 P/NSWITCH, Press 18# N.O /8MNPT BRACKET,ASSY ENG. AIR CleanerSWITCH, Temp 220 F NC Gold Contacts SENDER, Coolant Temperature 3/841 P/N 307271 CONNECTOR, Male 1/4 T X 1/4 D CONNECTOR, 1 Mjic X 1 MnptCONNECTOR, 1/4 Mnpt X 1/4 Tube 200PSI DEG RELIEF, 1/2 NPT 175 PSIBOLT, Battery Hold Down BRACKET, Battery Hold DownBATTERY, 12VOLT 650CCA a VALVE, Service 1 X 3/4-Y VentedLA PORTE, 45 P/NPANEL, DUS OIL Fill Access PANEL, DUS Rear AccessLatch ADJ Lever C2-33-35 WASHER, Flat Wide 1/4 SS47 P/N John Deere 4045 DF Engine
Top Page Image Contents