Omega Engineering 185-210 DUS User Modification, Tampering with Noise Control System Prohibited

Page 7

USER MODIFICATION

This Boss compressor incorporates numerous features to minimize noise emissions from the unit during operation. This configuration has been tested for noise emissions at conditions specified by the U.S. Environmental Protection Agency. Conformance to regulations requires the incorporation of the following notification and definition in the OPERATION AND MAINTENANCE MANUAL.

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED

Federal law prohibits the following act:

1.The removal, rendering inoperative, other than for purposes of maintenance, repair or replacement of any device or element of design incorporated into any new compressor for the purpose for noise control prior to its sale or delivery to the ultimate purchaser.

2.The use of the compressor after such device or element of design has been removed or rendered inoperative by any person.

Among the acts included in the prohibition against tampering are those listed:

1.Removal or rendering inoperative any of the following:

a.The engine exhaust system including the manifold, muffler or tailpipe.

b.Any of the enclosure components and associated sound barrier materials.

c.The sound baffles in the intake, exhaust and cooling system gas paths.

d.The air intake system including the air cleaner, the intake ducting, valve cover and gaskets.

2.Removal of any of the following:

a.Engine mounts or other sound isolating barriers in the system.

b.Fan shrouding and sound hood.

3.Operation of the compressor with any of the enclosure doors open.

8

P/N: 307271

Image 7

Contents Serial Number Model Number 06/17/2008 MCM Omega ToolPage Table of Contents Page OWNER’S Responsibility IntroductionAIR Compressor Safety Precautions Tampering with Noise Control System Prohibited User ModificationCompressor USE and Compressed AIR SafetyParking Before Starting the CompressorLifting ServicingIntroduction DescriptionRotary Compressor Components Engine Components Frame ChassisEnclosure Instrument Panel DoorOperation Starting ProcedureEmergency Shutdown Procedure Routine Shutdown Procedure15 P/N MaintenanceEngine Fuel Specifications Cold Weather FuelMixtures Engine Cooling SpecificationsOIL Filter Replacement Engine OIL and FilterCoolant Level Radiator Pressure CAPRadiator Compressor OILCompressor OIL Specifications 19 P/N Compressor OIL FilterElement Replacement Compressor & Engine AIR Filter MaintenanceElement Inspection Compressor OIL Thermostatic Valve Belts & Belt AdjustmentCleaning Oilthermostat Separator Element ReplacementAdjustment CONTROLS-OPERATION and AdjustmentsIdle Speed Adjustment Procedures Instruments BatteryPressure Regulator Adjustment Rated Speed AdjustmentDaily Operation Maintenance Schedule25 P/N Maintenance Schedule ChartCompressor AIR Filter Element Procedure for Ordering PartsTroubleshooting Troubleshooting27 P/N Symptom Cause Remedy Troubleshooting Chart29 P/N Clean or replace the element Boss INDUSTRIES, INC Genesis Drive LAPORTE, Warranty31 P/N Summary of Main Warranty Provisions 33 P/N WARRANTY/RETURN Goods InstructionsWarranty Claims Preparation of Part Return Return or Warranty Claims Filing ProceduresDamage in Transit General35 P/N Screw Compressor AIR-END Exchange ProgramPage 37 P/N Section Assembly DrawingsCoolers & PARTS, Omega 185-210 DUS Frame & PARTS, Omega 185-210 DUSEngine & PARTS, Omega 185-210 DUS Compressor & PARTS, Omega 185-210 DUSREV Description Date ENG Revision History 39 P/NSENDER, Coolant Temperature 3/8 BRACKET,ASSY ENG. AIR CleanerSWITCH, Press 18# N.O /8MNPT SWITCH, Temp 220 F NC Gold Contacts41 P/N 307271 RELIEF, 1/2 NPT 175 PSI CONNECTOR, 1 Mjic X 1 MnptCONNECTOR, Male 1/4 T X 1/4 D CONNECTOR, 1/4 Mnpt X 1/4 Tube 200PSI DEGVALVE, Service 1 X 3/4-Y Vented BRACKET, Battery Hold DownBOLT, Battery Hold Down BATTERY, 12VOLT 650CCA aLA PORTE, 45 P/NWASHER, Flat Wide 1/4 SS PANEL, DUS Rear AccessPANEL, DUS OIL Fill Access Latch ADJ Lever C2-33-3547 P/N John Deere 4045 DF Engine