Omega Engineering 185-210 DUS, JD 4045 manual Summary of Main Warranty Provisions

Page 31

SUMMARY OF MAIN WARRANTY PROVISIONS

As claims, policies and procedures are governed by the terms of the BOSS Industries, Inc. (BOSS) warranty, it is necessary to outline some of the more important provisions.

The BOSS warranty applies only to new and unused products, which, after shipment from the factory, have not been altered, changed, repaired or mistreated in any manner whatsoever. Normal maintenance items such as lubricants and filters are not warrantable items.

Parts not of BOSS manufacture are warranted only to the extent they are warranted by the original manufacturer.

Damage resulting from abuse, neglect, misapplication or overloading of a machine, accessory or part is not covered under warranty.

Deterioration or wear occasioned by chemical and/or abrasive action or excessive heat shall not constitute defects.

Parts replacement and/or correction of defective workmanship will normally be handled by BOSS Industries, Inc. or their authorized distributor.

Failure to file a detailed warranty claim/service report for each occurrence of material defect of defective workmanship will cause warranty claim to be rejected.

Defective material must be returned within 30 days of receipt of shipping instructions. Failure to do so within specified time will result in forfeiture of claim.

The distributor is responsible for the initial investigation and write up of the warranty claim.

Distributor shall be allowed no more than 30 days from date of repair to file a warranty claim/service report.

Warranty for failure of BOSS replacement parts covers the net cost of the part only, not labor and mileage.

The BOSS warranty does not cover diagnostic calls and travel. That is time spent traveling to the machine to analyze the problem and returning with the proper tools and parts to correct the problem.

Boss will deduct from allowable credits for excess freight caused by sender failing to follow return shipping instructions.

Distributors or end-user automatically deducting the value of a warranty claim from outstanding balances due and payable to BOSS prior to receiving written notification of BOSS approval of the warranty claim may be subject to forfeiture of the entire claim.

32

P/N: 307271

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Serial Number Model Number 06/17/2008 MCM Omega ToolPage Table of Contents Page OWNER’S Responsibility IntroductionAIR Compressor Safety Precautions Tampering with Noise Control System Prohibited User ModificationCompressor USE and Compressed AIR SafetyParking Before Starting the CompressorLifting ServicingIntroduction DescriptionRotary Compressor Components Engine Components Frame ChassisEnclosure Instrument Panel DoorOperation Starting ProcedureEmergency Shutdown Procedure Routine Shutdown Procedure15 P/N MaintenanceEngine Fuel Specifications Cold Weather FuelMixtures Engine Cooling SpecificationsOIL Filter Replacement Engine OIL and FilterCoolant Level Radiator Pressure CAPRadiator Compressor OILCompressor OIL Specifications 19 P/N Compressor OIL FilterElement Replacement Compressor & Engine AIR Filter MaintenanceElement Inspection Compressor OIL Thermostatic Valve Belts & Belt AdjustmentCleaning Oilthermostat Separator Element ReplacementAdjustment CONTROLS-OPERATION and AdjustmentsIdle Speed Adjustment Procedures Instruments BatteryPressure Regulator Adjustment Rated Speed AdjustmentDaily Operation Maintenance Schedule25 P/N Maintenance Schedule ChartCompressor AIR Filter Element Procedure for Ordering PartsTroubleshooting Troubleshooting27 P/N Symptom Cause Remedy Troubleshooting Chart29 P/N Clean or replace the element Boss INDUSTRIES, INC Genesis Drive LAPORTE, Warranty31 P/N Summary of Main Warranty Provisions 33 P/N WARRANTY/RETURN Goods InstructionsWarranty Claims Preparation of Part Return Return or Warranty Claims Filing ProceduresDamage in Transit General35 P/N Screw Compressor AIR-END Exchange ProgramPage 37 P/N Section Assembly DrawingsCoolers & PARTS, Omega 185-210 DUS Frame & PARTS, Omega 185-210 DUSEngine & PARTS, Omega 185-210 DUS Compressor & PARTS, Omega 185-210 DUSREV Description Date ENG Revision History 39 P/NSENDER, Coolant Temperature 3/8 BRACKET,ASSY ENG. AIR CleanerSWITCH, Press 18# N.O /8MNPT SWITCH, Temp 220 F NC Gold Contacts41 P/N 307271 RELIEF, 1/2 NPT 175 PSI CONNECTOR, 1 Mjic X 1 MnptCONNECTOR, Male 1/4 T X 1/4 D CONNECTOR, 1/4 Mnpt X 1/4 Tube 200PSI DEGVALVE, Service 1 X 3/4-Y Vented BRACKET, Battery Hold DownBOLT, Battery Hold Down BATTERY, 12VOLT 650CCA aLA PORTE, 45 P/NWASHER, Flat Wide 1/4 SS PANEL, DUS Rear AccessPANEL, DUS OIL Fill Access Latch ADJ Lever C2-33-3547 P/N John Deere 4045 DF Engine
Top Page Image Contents