Omega Engineering FP-6000 manual Servicing North America, Servicing Europe

Page 2

OMEGAnet® Online Service

www.omega.com

Internet e-mail

info@omega.com

Servicing North America:

USA:

One Omega Drive, P.O. Box 4047

 

ISO 9001 Certified

Stamford CT 06907-0047

 

 

TEL: (203) 359-1660

FAX: (203) 359-7700

 

e-mail: info@omega.com

 

Canada:

976 Bergar

 

 

Laval (Quebec) H7L 5A1

 

 

TEL: (514) 856-6928

FAX: (514) 856-6886

 

e-mail: info@omega.ca

 

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA®

 

Customer Service: 1-800-622-2378 / 1-800-622-BEST®

 

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN®

 

TELEX: 996404 EASYLINK: 62968934

CABLE: OMEGA

Mexico:

En Español: (001) 203-359-7803

e-mail: espanol@omega.com

 

FAX: (001) 203-359-7807

info@omega.com.mx

Servicing Europe:

Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands

TEL: +31 (0)20 3472121FAX: +31 (0)20 6434643

Toll Free in Benelux: 0800 0993344

e-mail: nl@omega.com

Czech Republic:

France:

Germany/Austria:

Rudé armády 1868, 733 01 Karviná 8

 

TEL: +420 (0)69 6311899

FAX: +420 (0)69 6311114

Toll Free: 0800-1-66342

e-mail: czech@omega.com

9, rue Denis Papin,

78190 Trappes

 

TEL: +33 (0)130 621

400

FAX: +33 (0)130 699 120

Toll Free in France: 0800-4-06342

e-mail: france@omega.com

Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

TEL: +49 (0)7059 9398-0FAX: +49 (0)7056 9398-29

Toll Free in Germany: 0800 639 7678

e-mail: germany@omega.com

United Kingdom:

One Omega Drive, River Bend Technology Centre

ISO 9002 Certified

Northbank, Irlam, Manchester

 

 

M44 5EX United Kingdom

 

 

TEL: +44 (0)161 777 6611

FAX: +44 (0)161 777 6622

 

Toll Free in United Kingdom: 0800-488-488

 

e-mail: sales@omega.co.uk

 

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.

WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.

Image 2
Contents User’s Guide Servicing Europe Servicing North AmericaFor immediate technical or application assistance Table of Contents Page Important Safety Information Warranty Record Type Omega FP-6000 SeriesTheory of Operation Chapter IntroductionDescription Sensor Position Chapter Installation and WiringLocation of Fitting Sensor Wiring +30Hardware, Hot-Tap Sensor Standard Fitting InstallationHardware, Standard Sensor 11/4 in mm diameter drill Pipe thread sealant Tape measureThread brass sensor nut into pipe fitting Hot-Tap Fitting InstallationRemove brass sensor nut from sensor Calculating the H Dimension Wall ThicknessRecord your pipes H dimension for future reference Hot-Tap Sensor = 15.00 pipe wall thickness 0.10 X I.DStandard Installation Sensor flange Alignment rod Direction of flow Thread one jam nut and lower hex nut onto Hot-Tap InstallationStep Make sure the bleed valve is closed full clockwise position Direction of flowUsing the Hot-Tap Installation Tool Protector plate Installation tool shaft Upper hex nuts Hot-Tap Sensor Removal ChapterStandard Sensor Removal Into the port to prevent damageCap nuts Installation tool Replacement Parts Chapter Maintenance and Replacement PartsMaintenance Rotor Replacement Procedure Wrought Steel Pipe Per Ansi DimensionsDimensions for Standard Sensors Conversion Stainless Steel Pipe Per Ansi B36.19 Mm = inchesDimensions for Hot-Tap Sensors Factors Stainless Steel GPM/HZ LPM/HZFactors Wrought Steel Factors Plastic Pipe GPM/HZ LPM/HZSpecifications General DataSpecifications WARRANTY/DISCLAIMER OMEGA…Of Course