Schneider Electric Altivar 212 Analog inputs values FE35, FE36, Digital outputs command FA50

Page 56

Parameter list

Analog inputs values (FE35, FE36)

[Analog input VIA value] (FE35)

[Analog input VIB value] (FE36)

Data: 10bit resolution (Data range 0 to 1023)

Digital outputs command (FA50)

The digital outputs (relays) of the drive can be controlled directly by communication.

Before controlling them, select Function Number 38 or 39 in Output terminal function selection ([FL Relay Function] (F132)) and select Function Number 40 or 41 in Output terminal function selection ([RY Relay Function 1] (F130) ,[RY Relay Function 2] (F137)).

Bit

Output Terminal Function

0

1

 

 

 

 

0

Relay FL (F132)

OFF

ON

 

 

 

 

1

Relay RY (F130 and F137)

OFF

ON

 

 

 

 

2 to 15

Reserved

-

-

 

 

 

 

Example: Controlling only relay RY by communication

Set 40 [Ser. data relay RY] in F130 in advance.

Set "0002H" in FA50 to turn relay RY on.

Analog outputs command (FA51)

The analog output FM on the drive can be controlled directly by communication.

Select 18 [Com data] in [AO funct. selection] (FMSL) parameter before controlling them.

The data adjustment range is 0 to 1023 (10bit resolution). Refer to "Meter Setting and adjustment" in the ATV 212 programming manual for complete information.

Communication feedback (FA49)

Damper function. This function applies to the ventilation ducts. The aim is to control the opening of the duct (shutter device called a "damper") when the fan starts up.

Damper opening command

The opening command can be assigned to a relay via the F130 or F132 parameters to the function [Damper] 68 or [Inv. damper] 69. The damper is closed automatically when there is no longer an opening command.

Damper opening feedback

Opening is controlled by a bit or a logic input that can be assigned via the F111 or F112 or F113 parameters to the function 73. The corresponding logic input or bit can be configured via the parameter [Damper fdb type] F580.

When there is an inconsistency, the drive goes on a [Damper fault 1] Fd1 if the damper does not open and on a [Damper fault 2] Fd2 if it does not close.

The parameter [Time open damper] F581 can be used to delay tripping on an opening fault when a run command is sent and the parameter [Time close damper] F582 delays the closing fault when a stop command is sent.

Damper

ATV 212

Control

Feedback

 

U V W

0

Rp

P24

LIp

Damper open contact

Damper opening

M

3

Flow of air

Fan

56

S1A53844 01/2011

Image 56
Contents Altivar S1A53844 01/2011 Table of Contents Table of Contents Safety Information Important InformationAbout the Book At a GlanceHazard of Electric SHOCK, Explosion or ARC Flash S1A53844 01/2011 Introduction Introduction Topic Hardware setupWhats in this Chapter? Pin out of the Open Style Modbus connector RJ45Cross section Tightening torqueConnection via Open Style wiring system Pin out of the RJ45 Modbus connectorPin Signal Open Style ReferenceConnection via RJ45 wiring system Connection accessoriesConnecting cables RJ45 ReferenceProtection Against Interference Description of terminals PTC resistor value F646GND Hardware setup Configuration Configuration of the communication parameters Access to the parametersParameters Modbus Adjustment range Default Valid Address AfterConfiguration of the control source Parameters Modbus SettingControl by the Modbus network CommunicationParameters Setting Default ValidControl by the terminals, monitoring by the Modbus network Parameters Modbus Setting Default Valid Parameters Modbus Setting Default Valid Address Com channel choice F807 Communication Menu COM submenuLI R selection F112 LI R selectionParameters Location Remote spd ref 2 F207Frequency source VIA VIAComplete control diagram Commands CMOdConfiguration of the indirect blocks ConfigurationConfiguration of the communication interruption Configure the drive behaviour Parameter Modbus Setting Default Valid AddressCommunication detected fault 16#851 2129Configuration Modbus services RTU mode Principle of the Modbus protocolSlave Slave j Slave k Slave address Function code DataFunction 3, quantity = Modbus functions availableRead one word Status info Read indirect blockFunction 3, quantity = 1 Read indirect block of 2 parameters Write Single Register Write multiple registers Function 16 = 16#10, quantity =1Speed Setpoint Command word Frequency SetpointWrite indirect block Request 6C 7E Response Read Device Identification 43/14 Error response Exception codeModbus services Parameter list Auto ramp AUI Disabled Manual Setting of Max frequency FHReferring to the Altivar 212 programming manual GeneralCommands from serial communication List of control parametersSetpoints from serial communication Outputs control from serial communicationList of monitoring parameters StatusFrequency and speed Current and torquePower and energy MaintenanceTrip and alarm codes ValuesBit Specifications Remarks CommandsCommand word FA00 Command word 2 FA20 Energy reset bitExamples Over-current stall level change bitSpeed setpoint FA13 SetpointsFrequency setpoint FA01 Status Status word FE0I Fd01Command mode status FE45 Setpoint mode status FE46Status word 2 FE42 Fd42 Status word 3 FE49 Fd49Alarm of run time FE79 Trip and alarm codesAlarm code FC91 Code Value Description Hexadecimal number Decimal number Monitoring and control of I/O from communication Digital inputs status Fd06, FE06Digital outputs status Fd07, FE07 Bit Terminal name Function parameter titleDigital outputs command FA50 Analog outputs command FA51Damper opening command Analog inputs values FE35, FE36F580 = 3 Drive model code F805 Model Voltage Power Rating Code FB05 Class FB72bit8Identification ATV212WU15N4C S1A53844 01/2011 Appendix RS485 standard Modbus 2-wire standard schematicSchematic diagram Migration Commissioning Migration ATV21 ATV212For example ATV212Modbus manualENS1A5384401 S1A53844 01/2011