Carrier 50RTP03-20 specifications Alarm

APPENDIX A — WSHP SCREEN OPEN CONFIGURATION (cont)

SCREEN NAME		PASSWORD	POINT NAME	EDITABLE	RANGE	DEFAULT	NOTES
		LEVEL
							Defines the hysteresis applied above
			SPT Occupied Alarm	X	2 - 20 ° F	5 ° F	the cooling and below the heating set
			Hysteresis				points before an alarm condition will
							occur
							Used to calculate the delay time before
			SPT Alarm Delay	X	0 - 30 min per degree	10 min	an alarm is generated after the alarm
							condition occurs
			SPT Unoccupied Low	X	35 - 90 ° F	45 ° F	Defines the fixed unoccupied
			Alarm Temperature				ow SPT alarm limit
			SPT Unoccupied High	X	45 - 100 ° F	95 ° F	Defines the fixed unoccupied
			Alarm Temperature				high SPT alarm limit
			SAT Low SAT	X	15 - 90 ° F	45 ° F	Defines the fixed minimum
			Alarm Limit				SAT alarm limit
			SAT High SAT	X	90 - 175 ° F	120 ° F	Defines the fixed maximum
			Alarm Limit				SAT alarm limit
			Condensate Overflow				Defines the delay time before an alarm
				X	5 - 600 sec	10 sec	is generated after the alarm condition
			Alarm Delay
							occurs
			Space Humidity Occupied	X	45% - 100%	100%	Defines the fixed occupied
			High Alarm Limit				high space RH alarm limit
			Space Humidity Alarm				Used to calculate the delay time before
Configuration				X	0 - 30 min per % RH	5 min	an alarm is generated after the alarm
			Delay
							condition occurs
	→	Admin Password	Space Humidity Unoccu-	X	45% - 100%	100%	Defines the fixed unnoccupied
		level access only	pied High Alarm Limit				high space RH alarm limit
	Alarm		IAQ/Ventilation Occupied	X	0 - 9999 ppm	1100 ppm	Defines the fixed occupied high
Configuration			High Alarm Limit				space IAQ/Ventilation alarm limit
			IAQ/Ventilation				Used to calculate the delay time before
				X	0.1 - 1.0 min per ppm	0.25 min	an alarm is generated after the alarm
			Alarm Delay
							condition occurs
			Rnet Sensor SPT Alarm	X	Ignore/Display	Ignore	Determines if the SPT alarm is
							displayed on the local Rnet sensor
			Rnet Sensor SAT Alarm	X	Ignore/Display	Ignore	Determines if the SAT alarm is
							displayed on the local Rnet sensor
			Rnet Sensor Compressor				Determines if the Compressor Lockout
				X	Ignore/Display	Display	alarm is displayed on the local Rnet
			Lockout Alarm
							sensor
			Rnet Sensor Condenser				Determines if the Condenser Water
				X	Ignore/Display	Display	Temperature alarm is displayed on the
			Water Temperature Alarm
							local Rnet sensor
			Rnet Sensor Condensate				Determines if the Condensate
				X	Ignore/Display	Display	Overflow alarm is displayed on the
			Overflow Alarm
							local Rnet sensor
			Rnet Sensor Dirty	X	Ignore/Display	Display	Determines if the Dirty Filter alarm is
			Filter Alarm				displayed on the local Rnet sensor
			Rnet Sensor Space				Determines if the High Space
				X	Ignore/Display	Ignore	RH alarm is displayed on the
			High Humidity Alarm
							local Rnet sensor
Configuration			Loop Control Network				See TPI
			Number
	→		Loop Control Network				See TPI
			Address
Linkage			Number of Linked Heat				See TPI
			Pumps
	LEGEND
BAS — Building Automation System
DCV — Demand Controlled Ventilation
ECM	— Electronically Commutated Motor
IAQ	— Indoor Air Quality
OAT	— Outdoor Air Temperature
RH	— Relative Humidity
SAT — Supply Air Temperature
SPT	— Space Temperature
TPI	— Third Party Integration

55