Carrier 50VQP084-300 specifications A50-8437, 50VQP168-300 Unit Dimensions

ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW

V	F	a50-8437	19.3
19.3	D
	G	B
		D

	AIR OUT
		E
	RETURN AIR	NRP	AIR OUT
NRP			E
C	BSP
	S
	1		RETURN AIR
	Q	BSP
			S
	3
02	MSP
P				R
	01	CAP		NRP
			Control Box
	2			3
	CSP
		NRP
				M
		CSP	L	K
				A

			AIR OUT
				NRP
				AIR OUT
T		RETURN AIR		BSP
	4		2
				RETURN AIR
5	3	Control Box
4
U
		CSP+CAP	1	4
				5
N				4
				NRP
				CSP+MSP
NOTE 5

F

NRP

3

L

M

K

4.3

E

NRP

4

5

4

Service Access

3’ (91 cm)

Front and Back

(All Configurations)

F

3

CSP

			REAR RETURN TOP DISCHARGE						FRONT RETURN TOP DISCHARGE
BSP
D
	G					NRP
			D
AIR OUT	RETURN
	AIR							AIR OUT		F
									BSP
1				RETURN
	NRP
		AIR OUT		AIR					AIR OUT
							RETURN AIR
MSP								2
					4
	CAP			NRP					RETURN AIR
			Control Box
					5	3
							Control Box
2
				4
					4
										NRP
				5
					3
	NRP			4
		CSP					CSP+CAP	1	4
									5	3
									4
									NRP
					Side Service Access				CSP+MSP
					(See Note)
				REAR RETURN FRONT DISCHARGE			FRONT RETURN REAR DISCHARGE

LEGEND

BSP — Blower Service Panel

CAP — Control Access Panel

CSP — Compressor Service Panel

MSP — Motor Service Panel

NRP — Non-Removable Panel

NOTES:

1.All dimensions in centimeters.

2.Units require 91 cm clearance for water connections, CAP, CSP, MSP, and BSP service access.

3.Overall cabinet height dimension does not include duct flange when in top discharge configuration.

4.Overall cabinet width dimension does not include filter rack and duct flange when on front or back dis- charge configuration.

5.Side service access must be 91 cm on either side that connections are made. If no connections are made on a side, then service access can be 15 mm minimum.

6.While access to all removable panels is not required, installer should take care to comply with all building codes and allow adequate clearance for future field service.

7.Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT plugs are shipped loose in a plastic bag tied to the water leg in front of the unit. Installer must plug water inlet/outlet side not being connected to.

8.Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be tied inside the unit. Installer must untie the drain hose and connect to the condensate drain hole of installer’s choice.

9.Electrical access is available on either side (left or right) of unit and is also available (left or right) in the front of the unit.

10.Overall depth — add 7.9 cm for 2.5 or 5 cm filter. Add 13 cm for 10 cm filter.

	CONNECTIONS	50VQP168-240	50VQP300
1 Water Inlet (See Note 7)		2 in. FPT	21/2 in. FPT
2	Water Outlet (See Note 7)	2 in. FPT	21/2 in. FPT
3	Condensate Drain (See Note 8)	1 in. FPT	1 in. FPT
4	High Voltage Access (See Note 9)	13/8 in.	13/8 in.
5	Low Voltage Access (See Note 9)	7/8 in.	7/8 in.

		OVERALL				DISCHARGE				WATER				ELECTRICAL					RETURN AIR
					CONNECTIONS (cm)													CONNECTIONS (cm)
	CABINET (cm)									CONNECTIONS (cm)				KNOCKOUTS (cm)
UNIT						Duct Flange												(Using Return Air Opening)
50VQP	A		B	C	D	E			K	L	M							S	T
					Supply	Supply	F	G	1-Water	2-Water	3-	N	O1	O2	P	Q	R	Return	Return	U	V
	Depth		Width	Height
					Width	Depth			Inlet	Outlet	Condensate							Depth	Height
168-240	86.4		270.9	200.7	44.5	44.6	45.1	79.4	78.7	7.6	68.6	65.1	78.1	96.4	87.8	2.5	7.6	121.9	82.2	113.3	6.9
300	86.4		270.9	200.7	54.4	44.6	45.1	59.4	78.7	7.6	68.6	65.1	78.1	96.4	87.8	2.5	7.6	121.9	82.2	113.3	6.9

Fig. 3 — 50VQP168-300 Unit Dimensions

5