Carrier 50VQP084-300 specifications A50-8436, 50VQP084-150 Unit Dimensions

ALL CONFIGURATIONS REQUIRE SERVICE ACCESS AREA SHOWN BELOW

					19.3
		F	B
			D
19.3								F
		AIR OUT	NRP		NRP	AIR OUT
								BSP
a50-8436
	BSP			T
NRP		RETURN AIR
					RETURN AIR
		S		4
C
		1				2		NRP
	Q			5
			R
				U
	3		NRP	4	Control Box
02	CAP+MSP
		Control Box	3		3		4
								3 L
P				N			4 5
01	2			NRP	1			M
			M K
		L			CSP+CAP+MSP			K
	CSP

ANOTE 5

		REAR RETURN TOP DISCHARGE			FRONT RETURN TOP DISCHARGE
4.3	F
	D	RETURN AIR
		BSP					F
	E				BSP
	BSP				AIR OUT
NRP	AIR OUT
4		NRP
5		1
					RETURN AIR
			NRP				NRP
4	3			4
					2
	CAP+MSP			5
		Control Box
		4	3	4	Control Box
	2		5
		4
				3	4
							3
					4	5
	CSP			NRP	1
					CSP+CAP+MSP
			SIDE
			SERVICE ACCESS
			(SEE NOTE)
SERVICE ACCESS		REAR RETURN FRONT DISCHARGE
91 CM
					FRONT RETURN REAR DISCHARGE
FRONT AND BACK

LEGEND

BSP — Blower Service Panel

CAP — Control Access Panel

CSP — Compressor Service Panel

MSP — Motor Service Panel

NRP — Non-Removable Panel

NOTES:

1.All dimensions in centimeters.

2.Units require 0.9 m clearance for water connections, CAP, CSP, MSP, and BSP service access.

3.Overall cabinet height dimension does not include duct flange when in top discharge configuration.

4.Overall cabinet width dimension does not include filter rack and duct flange when on front or back dis- charge configuration.

5.Side service access must be 0.9 m on either side that connections are made. If no connections are made on a side, then service access can be 15 mm minimum.

6.While access to all removable panels is not required, installer should take care to comply with all building codes and allow adequate clearance for future field service.

7.Water inlet and water outlet connections are available on either side (left or right) of the unit. Two MPT plugs are shipped loose in a plastic bag tied to the water leg in front of the unit. Installer must plug water inlet/outlet side not being connected to.

8.Condensate drain is available on either side (left or right) of unit. Drain hose and drain connection will be tied inside the unit. Installer must untie the drain hose and connect to the condensate drain hole of installer’s choice.

9.Electrical access is available on either side (left or right) of unit and is also available (left or right) in the front of the unit.

10.Overall depth — add 7.9 cm for 2.5 or 5 cm filter. Add 13 cm for 10 cm filter.

1

2

3

4

5

CONNECTIONS	50VQP084-120	50VQP150
Water Inlet (See Note 7)	11/2 in. FPT	2 in. FPT
Water Outlet (See Note 7)	11/2 in. FPT	2 in. FPT
Condensate Drain (See Note 8)	1 in. FPT	1 in. FPT
High Voltage Access (See Note 9)	13/8 in.	13/8 in.
Low Voltage Access (See Note 9)	7/8 in.	7/8 in.

		OVERALL		DISCHARGE				WATER				ELECTRICAL					RETURN AIR
				CONNECTIONS (cm)												CONNECTIONS (cm)
	CABINET (cm)							CONNECTIONS (cm)				KNOCKOUTS (cm)
UNIT				Duct Flange												(Using Return Air Opening)
50VQP	A	B	C	D	E		K	L	M							S	T
				Supply	Supply	F	1-Water	1-Water	3-	N	O1	O2	P	Q	R	Return	Return	U	V
	Depth	Width	Height
				Width	Depth		Inlet	Outlet	Condesate							Depth	Height
084-120	86.4	134.9	200.7	44.5	44.6	45.1	78.7	7.6	68.6	65.1	78.7	96.4	87.7	2.5	7.6	121.9	82.2	113.3	6.9
150	86.4	134.9	200.7	54.4	44.6	45.1	78.7	7.6	68.6	65.1	78.7	96.4	87.7	2.5	7.6	121.9	82.2	113.3	6.9

Fig. 2 — 50VQP084-150 Unit Dimensions

4