DeWalt DWE46102 Switches, Slider Switch FIG, Spindle Lock FIG, Mounting NON-HUBBED Wheels FIG

Page 14

English

Switches

CAUTION: Hold the side handle and body of the tool firmly to maintain control of the tool at start up and during use and until the wheel or accessory stops rotating. Make sure the wheel has come to a complete stop before laying the tool down.

NOTE: To reduce unexpected tool movement, do not switch the tool on or off while under load conditions. Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.

SLIDER SWITCH (FIG. 6)

CAUTION: Before connecting the tool to a power supply, be sure the switch is in the off position by pressing the rear part of the switch and releasing. Ensure the switch is in the off position as described above after any interruption in power supply to the tool, such as the activation of a ground fault interrupter, throwing of a circuit breaker, accidental unplugging, or power failure. If the switch is locked on when the power is connected, the tool will start unexpectedly.

To start the tool, slide the ON/OFF

FIG. 6

switch (I) toward the front of the tool. To

 

I

stop the tool, release the ON/OFF

 

 

switch.

 

 

For continuous operation, slide the

 

 

switch toward the front of the tool

 

 

 

 

and press the forward part of the

 

 

switch inward. To stop the tool while

 

 

operating in continuous mode, press

 

 

the rear part of the switch and release.

 

 

12

SPINDLE LOCK (FIG. 7)

 

FIG. 7

The spindle lock (A) is provided to prevent the

 

spindle from rotating when

installing or

A

removing wheels. Operate the spindle lock

 

only when the tool is turned off, unplugged from the power supply, and has come to a complete stop. Do not engage the spindle lock while the tool is operating because damage to the tool will result. To engage the lock, depress the spindle lock button and rotate the spindle until you are unable to rotate the spindle further.

Mounting and Using Depressed Center Grinding Wheels and Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS (FIG. 1)

Hubbed wheels install directly on the 5/8"–11threaded spindle. Thread of accessory must match thread of spindle.

1.Backing flange is retained to the grinder by an O-ring (N) on the spindle. Remove backing flange by pulling and twisting flange away from the tool.

2.Thread the wheel on the spindle by hand.

3.Depress the spindle lock button and use a wrench to tighten the hub of the wheel.

4.Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel before turning the tool on may result in damage to the tool or the wheel.

MOUNTING NON-HUBBED WHEELS (FIG. 8)

Depressed center Type 27 grinding wheels must be used with included flanges. Refer to page 9 for more information.

1.Install the unthreaded backing flange (E) on spindle (B) with the raised section (pilot) against the wheel. Be sure the backing flange

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Guide D’UTILISATION Manual DE Instrucciones Page Work Area Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Electrical SafetyService Personal SafetyPower Tool USE and Care Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Polishing OperationsSafety Warnings Specific for Wire Brushing Operations Additional Safety Rules for GrindersSave These Instructions for Future USE Switch ProtectionPOWER-OFF Overload Protection ClutchComponents FIG Assembly and AdjustmentsMotor Become separated by more than 1/8 AccessoriesRotating the Gear Case FIg Mounting Guard Mounting and Removing GuardOperation Guards and FlangesSpindle Lock FIG SwitchesSlider Switch FIG Mounting and Removing Hubbed Wheels FIGEdge Grinding with Grinding Wheels FIG Surface Grinding with Grinding Wheels FIGWheels Mounting Sanding Backing Pads FIG Using Sanding Backing Pads FIGSurface Finishing with Sanding Flap Discs FIG Very Fine FinishingUsing Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Wheel and the work surface with wireMounting Closed Type 1 Guard , 17 Mounting and Using Cutting Type 1 WheelsUsing Cutting Wheels FIG Mounting Cutting WheelsThree Year Limited Warranty MaintenanceCleaning Addition to the warranty, Dewalt tools are covered by ourYear Free Service DAY Money Back GuaranteeSécurité EN Matière D’ÉLECTRICITÉ Définitions lignes directrices en Matière de sécuritéSécurité DU Lieu DE Travail Sécurité Personnelle Réparation Consignes DE Sécurité Pour Toutes LES OpérationsUtilisation ET Entretien D’UN Outil Électrique Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Dispositif E-CLUTCHMC Composant E-SWITCH Protectionmc Protection E-SWITCHConserver CES Consignes Pour Utilisation Ultérieure Assemblage ET Réglages MoteurDescription FIG Complete Electronic Controlmc Contrôle Électronique CompletMontage du dispositif de protection AccessoiresRotation du carter d’engrenage FIg Fixation DE LA Poignée LatéraleÊtre placé entre la broche et l’opérateur De travail voulue alors que le verrou estDésengagé. Le corps du capot devrait Pour maximiser la protection de ceReprendre Les étapes Enclenché et que ce dernier est installé surPour retirer le Capot ProtecteurInterrupteurs FonctionnementDispositifs de protection et brides Interrupteur Coulissant FIGDispositif DE Verrouillage DE LA Broche FIG Montage DE Meules Sans Moyeu FIGMeulage DE Bordure Avec DES Meules FIG Meulage DE Finition Avec DES Meules FIGSurface de la pièce, ce qui permet à Utilisation DES Patins DE Ponçage ET D’APPUI FIG Contact avec la surface de la pièceÉlevée Montage DES Patins D’APPUI ET DE Ponçage FIGSurface de travail Maximale à l’opérateur Montage et utilisation de meules de coupe typeMontage D’UN Dispositif DE Protection Fermé De serrage étant fermé’outil fonctionne à une vitesse élevée NettoyageUtilisation DES Meules DE Coupe FIG Contrat D’ENTRETIEN Gratuit D’UN AN RéparationsGarantie limitée de trois ans Garantie DE Remboursement DE 90 JoursSeguridad Eléctrica Definiciones Normas de seguridadSeguridad EN EL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Componentes Fig Protección Contra Sobrecarga POWER-OFFGuarde Estas Instrucciones Para Futuras Consultas Complete Electronic Control Control Electrónico CompletoAccesorios Como girar la caja de engranajes FIgEnsamblado Y Ajustes Instalación DE LA Agarradera Lateral FIGProtector tipo Disco de alambre Instalación del protectorProtector tipo Brida de respaldo Disco con cubo tipo Tuerca de fijación RoscadaColocado entre el eje y el operador, para proveer la máxima Protección al operadorInterruptores FuncionamientoProtectores y bridas Interruptor Deslizante FIGMontaje Y Remoción DE Discos CON Cubo FIG SuélteloBloqueo DEL EJE FIG Ensamblado DE Discos SIN Cubo FIGEsmerilado DE Bordes Condiscos Para Esmerilar FIG Esmerilado DE Superficies CON Discos Para Esmerilar FIGDiscos DE 1/4 Discos DE 1/8USO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIGAcabado DE Superficies CON Discos Para Lijar Aproximadamente Mueva la herramienta constantemente Montaje y uso de cepillos de alambre y discos de alambreAplicarla a la superficie de trabajo Montaje DEL Protector Cerrado Tipo Montaje y uso de los discos de corte TipoMantenga un ángulo de 5º a 10º entre la FIG De trabajo deseada. El cuerpo delMontaje DE LOS Discos DE Corte MantenimientoLimpieza USO DE Discos DE Corte FIGReparaciones Para Otras LocalidadesExcepciones Póliza de GarantíaGarantía limitada por tres años AÑO DE Servicio GratuitoEspecificaciones DWE46102Page

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents