DeWalt DWE46102 Surface Finishing with Sanding Flap Discs FIG, Mounting Sanding Backing Pads FIG

Page 16

English

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

3.Position yourself so that the open-underside of the wheel is facing away from you.

4.Once a cut is begun and a notch is established in the workpiece, do not change the angle of the cut. Changing the angle will cause the wheel to bend and may cause wheel breakage. Edge grinding wheels are not designed to withstand side pressures caused by bending.

5.Remove the tool from the work surface before turning the tool off. Allow the tool to stop rotating before laying it down.

WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result.

SURFACE FINISHING WITH SANDING FLAP DISCS (FIG. 11)

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to work surface, allowing the tool to operate at high speed. Sanding rate is greatest when the tool operates at high speed.

3.

Maintain a 5˚ to 10˚ angle between the

FIG. 11

 

tool and work surface.

 

4.

Continuously move the tool in a forward

5˚–10˚

 

and back motion to avoid creating

 

gouges in the work surface.

 

5.Remove the tool from work surface before turning tool off. Allow the tool to stop rotating before laying it down.

14

MOUNTING SANDING BACKING PADS (FIG. 12)

CAUTION: Proper guard must be

FIG. 12

P

reinstalled for grinding wheel, sanding

F

 

flap disc, wire brush or wire wheel

 

 

applications after sanding applications

 

 

are complete.

 

 

1.

Place or appropriately thread backing

 

 

 

pad (O) on the spindle.

 

 

2.

Place the sanding disc (P) on the

 

 

 

backing pad.

 

 

3.

While depressing spindle lock, thread

 

O

 

clamp nut (F) on spindle, piloting the

 

 

 

 

raised hub on the clamp nut into the center of sanding disc and backing pad.

4.Tighten the clamp nut by hand. Then depress the spindle lock button while turning the sanding disc until the sanding disc and clamp nut are snug.

5.To remove the wheel, grasp and turn the backing pad and sanding pad while depressing the spindle lock button.

USING SANDING BACKING PADS (FIG. 13)

Choose the proper grit sandpaper for your application. Sandpaper is available in various grits. Coarse grits yield faster material removal rates and a rougher finish. Finer grits yield slower material removal and a smoother finish.

Begin with coarse grit discs for fast, rough material removal. Move to a medium grit paper and finish with a fine grit disc for optimal finish.

Coarse

16 – 30 grit

Medium

36 – 80 grit

Fine Finishing

100 – 120 grit

Very Fine Finishing

150 – 180 grit

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Guide D’UTILISATION Manual DE Instrucciones Page Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Polishing OperationsSafety Warnings Specific for Wire Brushing Operations Additional Safety Rules for GrindersSwitch Protection POWER-OFF Overload ProtectionSave These Instructions for Future USE ClutchMotor Assembly and AdjustmentsComponents FIG Rotating the Gear Case FIg AccessoriesBecome separated by more than 1/8 Mounting Guard Mounting and Removing GuardOperation Guards and FlangesSwitches Slider Switch FIGSpindle Lock FIG Mounting and Removing Hubbed Wheels FIGWheels Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Using Sanding Backing Pads FIG Surface Finishing with Sanding Flap Discs FIGMounting Sanding Backing Pads FIG Very Fine FinishingMounting and Using Wire Brushes and Wire Wheels Mounting Wire CUP Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Wheel and the work surface with wireMounting and Using Cutting Type 1 Wheels Using Cutting Wheels FIGMounting Closed Type 1 Guard , 17 Mounting Cutting WheelsMaintenance CleaningThree Year Limited Warranty Addition to the warranty, Dewalt tools are covered by ourYear Free Service DAY Money Back GuaranteeSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Conserver CES Consignes Pour Utilisation Ultérieure Composant E-SWITCH Protectionmc Protection E-SWITCHDispositif E-CLUTCHMC Moteur Description FIGAssemblage ET Réglages Complete Electronic Controlmc Contrôle Électronique CompletAccessoires Rotation du carter d’engrenage FIgMontage du dispositif de protection Fixation DE LA Poignée LatéraleDe travail voulue alors que le verrou est Désengagé. Le corps du capot devraitÊtre placé entre la broche et l’opérateur Pour maximiser la protection de ceEnclenché et que ce dernier est installé sur Pour retirer leReprendre Les étapes Capot ProtecteurFonctionnement Dispositifs de protection et bridesInterrupteurs Interrupteur Coulissant FIGDispositif DE Verrouillage DE LA Broche FIG Montage DE Meules Sans Moyeu FIGSurface de la pièce, ce qui permet à Meulage DE Finition Avec DES Meules FIGMeulage DE Bordure Avec DES Meules FIG Contact avec la surface de la pièce ÉlevéeUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage DES Patins D’APPUI ET DE Ponçage FIGSurface de travail Montage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection FerméMaximale à l’opérateur De serrage étant ferméUtilisation DES Meules DE Coupe FIG Nettoyage’outil fonctionne à une vitesse élevée Réparations Garantie limitée de trois ansContrat D’ENTRETIEN Gratuit D’UN AN Garantie DE Remboursement DE 90 JoursSeguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Protección Contra Sobrecarga POWER-OFF Guarde Estas Instrucciones Para Futuras ConsultasComponentes Fig Complete Electronic Control Control Electrónico CompletoComo girar la caja de engranajes FIg Ensamblado Y AjustesAccesorios Instalación DE LA Agarradera Lateral FIGInstalación del protector Protector tipo Brida de respaldo Disco con cubo tipoProtector tipo Disco de alambre Tuerca de fijación RoscadaColocado entre el eje y el operador, para proveer la máxima Protección al operadorFuncionamiento Protectores y bridasInterruptores Interruptor Deslizante FIGSuéltelo Bloqueo DEL EJE FIGMontaje Y Remoción DE Discos CON Cubo FIG Ensamblado DE Discos SIN Cubo FIGEsmerilado DE Superficies CON Discos Para Esmerilar FIG Discos DE 1/4Esmerilado DE Bordes Condiscos Para Esmerilar FIG Discos DE 1/8Acabado DE Superficies CON Discos Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar Aplicarla a la superficie de trabajo Montaje y uso de cepillos de alambre y discos de alambreAproximadamente Mueva la herramienta constantemente Montaje y uso de los discos de corte Tipo Mantenga un ángulo de 5º a 10º entre la FIGMontaje DEL Protector Cerrado Tipo De trabajo deseada. El cuerpo delMantenimiento LimpiezaMontaje DE LOS Discos DE Corte USO DE Discos DE Corte FIGReparaciones Para Otras LocalidadesPóliza de Garantía Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoEspecificaciones DWE46102Page

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents