DeWalt DWE46102 instruction manual Safety Warnings Specific for Sanding Operations

Page 7

of wheel is exposed towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel.

c)Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

d)Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

e)Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Additional Safety Warnings Specific for Abrasive Cutting-Off Operations

a)Do not "jam" the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

b)Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.

c)When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback

5

may occur. Investigate and take corrective action to eliminate the cause of wheel binding.

d)Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.

e)Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

f)Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Specific for Sanding Operations

a)Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

Safety Warnings Specific for Polishing Operations

a)Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece.

English

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Guide D’UTILISATION Manual DE Instrucciones Page Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Polishing Operations Safety Warnings Specific for Sanding OperationsAdditional Safety Rules for Grinders Safety Warnings Specific for Wire Brushing OperationsClutch Switch ProtectionPOWER-OFF Overload Protection Save These Instructions for Future USEMotor Assembly and AdjustmentsComponents FIG Rotating the Gear Case FIg AccessoriesBecome separated by more than 1/8 Mounting and Removing Guard Mounting GuardGuards and Flanges OperationMounting and Removing Hubbed Wheels FIG SwitchesSlider Switch FIG Spindle Lock FIGWheels Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Very Fine Finishing Using Sanding Backing Pads FIGSurface Finishing with Sanding Flap Discs FIG Mounting Sanding Backing Pads FIGWheel and the work surface with wire Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire WheelsMounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsUsing Cutting Wheels FIG Mounting Closed Type 1 Guard , 17Addition to the warranty, Dewalt tools are covered by our MaintenanceCleaning Three Year Limited WarrantyDAY Money Back Guarantee Year Free ServiceSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Conserver CES Consignes Pour Utilisation Ultérieure Composant E-SWITCH Protectionmc Protection E-SWITCHDispositif E-CLUTCHMC Complete Electronic Controlmc Contrôle Électronique Complet MoteurDescription FIG Assemblage ET RéglagesFixation DE LA Poignée Latérale AccessoiresRotation du carter d’engrenage FIg Montage du dispositif de protectionPour maximiser la protection de ce De travail voulue alors que le verrou estDésengagé. Le corps du capot devrait Être placé entre la broche et l’opérateurCapot Protecteur Enclenché et que ce dernier est installé surPour retirer le Reprendre Les étapesInterrupteur Coulissant FIG FonctionnementDispositifs de protection et brides InterrupteursMontage DE Meules Sans Moyeu FIG Dispositif DE Verrouillage DE LA Broche FIGSurface de la pièce, ce qui permet à Meulage DE Finition Avec DES Meules FIGMeulage DE Bordure Avec DES Meules FIG Montage DES Patins D’APPUI ET DE Ponçage FIG Contact avec la surface de la pièceÉlevée Utilisation DES Patins DE Ponçage ET D’APPUI FIGSurface de travail De serrage étant fermé Montage et utilisation de meules de coupe typeMontage D’UN Dispositif DE Protection Fermé Maximale à l’opérateurUtilisation DES Meules DE Coupe FIG Nettoyage’outil fonctionne à une vitesse élevée Garantie DE Remboursement DE 90 Jours RéparationsGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANSeguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Complete Electronic Control Control Electrónico Completo Protección Contra Sobrecarga POWER-OFFGuarde Estas Instrucciones Para Futuras Consultas Componentes FigInstalación DE LA Agarradera Lateral FIG Como girar la caja de engranajes FIgEnsamblado Y Ajustes AccesoriosTuerca de fijación Roscada Instalación del protectorProtector tipo Brida de respaldo Disco con cubo tipo Protector tipo Disco de alambreProtección al operador Colocado entre el eje y el operador, para proveer la máximaInterruptor Deslizante FIG FuncionamientoProtectores y bridas InterruptoresEnsamblado DE Discos SIN Cubo FIG SuélteloBloqueo DEL EJE FIG Montaje Y Remoción DE Discos CON Cubo FIGDiscos DE 1/8 Esmerilado DE Superficies CON Discos Para Esmerilar FIGDiscos DE 1/4 Esmerilado DE Bordes Condiscos Para Esmerilar FIGAcabado DE Superficies CON Discos Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar Aplicarla a la superficie de trabajo Montaje y uso de cepillos de alambre y discos de alambreAproximadamente Mueva la herramienta constantemente De trabajo deseada. El cuerpo del Montaje y uso de los discos de corte TipoMantenga un ángulo de 5º a 10º entre la FIG Montaje DEL Protector Cerrado TipoUSO DE Discos DE Corte FIG MantenimientoLimpieza Montaje DE LOS Discos DE CortePara Otras Localidades ReparacionesAÑO DE Servicio Gratuito Póliza de GarantíaGarantía limitada por tres años ExcepcionesDWE46102 EspecificacionesPage

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents