DeWalt DWE46102 instruction manual Operation, Guards and Flanges

Page 13

1.Open the guard latch (J), and align the lugs (K) on the guard with the slots on the gear case (L). This will align the lugs on the guard with the slots on the gear case cover.

2.Push the guard down until the guard lugs engage and rotate freely in the groove on the gear case hub.

3.With the guard latch open, rotate the guard (F) into the desired working position. The guard body should be positioned between the spindle and the operator to provide maximum operator protection.

FIG. 4

K

L

J

CAUTION: If the guard cannot be tightened by the adjusting clamp, do not use the tool. To reduce the risk of personal injury, take the tool and guard to a service center to repair or replace the guard.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose; 1/4" (6.35 mm) thick wheels are designed for surface grinding while 1/8" (3.17 mm) wheels are designed for edge grinding. Cutting can also be performed by using a Type 1 wheel and a Type 1 guard.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

English

4. Close the guard latch to secure the

F

guard on the gear case. You should not

 

be able to rotate the guard by hand when the latch is closed. Do not operate the grinder with a loose guard or with the guard latch in open position.

5. To remove the guard, follow the procedure above in reverse order.

NOTE: The guard is pre-adjusted to the diameter of the gear case hub at the factory. FIG. 5

If, after a period of time, the guard becomes loose, tighten the adjusting screw (M) with guard latch in the closed position with guard installed on the tool.

CAUTION: Do not tighten the adjusting screw with the guard latch in the open position. Undetectable damage to the guard M or the mounting hub may result.

11

Guards and Flanges

It is important to choose the correct guards and flanges to use with the grinder accessories. See page 9–10 and this page for the correct accessories.

NOTE: Edge grinding and cutting can be performed with Type 27 wheels designed and specified for this purpose.

WARNING: Accessories must be rated for at least the speed recommended on the tool warning label. Wheels and other accessories running over rated accessory speed may burst and cause injury. Every unthreaded accessory must have a 7/8" arbor hole. If it does not, it may have been designed for a circular saw and should not be used. Use only the accessories shown on pages 9–10. Accessory ratings must be above listed minimum wheel speed as shown on tool nameplate.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide D’UTILISATION Manual DE Instrucciones Page General Power Tool Safety Warnings Definitions Safety GuidelinesWork Area Safety Electrical SafetyPower Tool USE and Care Personal SafetyService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Polishing Operations Safety Warnings Specific for Sanding OperationsAdditional Safety Rules for Grinders Safety Warnings Specific for Wire Brushing OperationsPOWER-OFF Overload Protection Switch ProtectionSave These Instructions for Future USE ClutchMotor Assembly and AdjustmentsComponents FIG Rotating the Gear Case FIg AccessoriesBecome separated by more than 1/8 Mounting and Removing Guard Mounting GuardGuards and Flanges OperationSlider Switch FIG SwitchesSpindle Lock FIG Mounting and Removing Hubbed Wheels FIGWheels Surface Grinding with Grinding Wheels FIGEdge Grinding with Grinding Wheels FIG Surface Finishing with Sanding Flap Discs FIG Using Sanding Backing Pads FIGMounting Sanding Backing Pads FIG Very Fine FinishingMounting Wire CUP Brushes and Wire Wheels Mounting and Using Wire Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Wheel and the work surface with wireUsing Cutting Wheels FIG Mounting and Using Cutting Type 1 WheelsMounting Closed Type 1 Guard , 17 Mounting Cutting WheelsCleaning MaintenanceThree Year Limited Warranty Addition to the warranty, Dewalt tools are covered by ourDAY Money Back Guarantee Year Free ServiceSécurité DU Lieu DE Travail Définitions lignes directrices en Matière de sécuritéSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Utilisation ET Entretien D’UN Outil Électrique Consignes DE Sécurité Pour Toutes LES OpérationsRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Conserver CES Consignes Pour Utilisation Ultérieure Composant E-SWITCH Protectionmc Protection E-SWITCHDispositif E-CLUTCHMC Description FIG MoteurAssemblage ET Réglages Complete Electronic Controlmc Contrôle Électronique CompletRotation du carter d’engrenage FIg AccessoiresMontage du dispositif de protection Fixation DE LA Poignée LatéraleDésengagé. Le corps du capot devrait De travail voulue alors que le verrou estÊtre placé entre la broche et l’opérateur Pour maximiser la protection de cePour retirer le Enclenché et que ce dernier est installé surReprendre Les étapes Capot ProtecteurDispositifs de protection et brides FonctionnementInterrupteurs Interrupteur Coulissant FIGMontage DE Meules Sans Moyeu FIG Dispositif DE Verrouillage DE LA Broche FIGSurface de la pièce, ce qui permet à Meulage DE Finition Avec DES Meules FIGMeulage DE Bordure Avec DES Meules FIG Élevée Contact avec la surface de la pièceUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage DES Patins D’APPUI ET DE Ponçage FIGSurface de travail Montage D’UN Dispositif DE Protection Fermé Montage et utilisation de meules de coupe typeMaximale à l’opérateur De serrage étant ferméUtilisation DES Meules DE Coupe FIG Nettoyage’outil fonctionne à une vitesse élevée Garantie limitée de trois ans RéparationsContrat D’ENTRETIEN Gratuit D’UN AN Garantie DE Remboursement DE 90 JoursSeguridad EN EL Área DE Trabajo Definiciones Normas de seguridadSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Guarde Estas Instrucciones Para Futuras Consultas Protección Contra Sobrecarga POWER-OFFComponentes Fig Complete Electronic Control Control Electrónico CompletoEnsamblado Y Ajustes Como girar la caja de engranajes FIgAccesorios Instalación DE LA Agarradera Lateral FIGProtector tipo Brida de respaldo Disco con cubo tipo Instalación del protectorProtector tipo Disco de alambre Tuerca de fijación RoscadaProtección al operador Colocado entre el eje y el operador, para proveer la máximaProtectores y bridas FuncionamientoInterruptores Interruptor Deslizante FIGBloqueo DEL EJE FIG SuélteloMontaje Y Remoción DE Discos CON Cubo FIG Ensamblado DE Discos SIN Cubo FIGDiscos DE 1/4 Esmerilado DE Superficies CON Discos Para Esmerilar FIGEsmerilado DE Bordes Condiscos Para Esmerilar FIG Discos DE 1/8Acabado DE Superficies CON Discos Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIGUSO DE Almohadillas DE Respaldo Para Lijar Aplicarla a la superficie de trabajo Montaje y uso de cepillos de alambre y discos de alambreAproximadamente Mueva la herramienta constantemente Mantenga un ángulo de 5º a 10º entre la FIG Montaje y uso de los discos de corte TipoMontaje DEL Protector Cerrado Tipo De trabajo deseada. El cuerpo delLimpieza MantenimientoMontaje DE LOS Discos DE Corte USO DE Discos DE Corte FIGPara Otras Localidades ReparacionesGarantía limitada por tres años Póliza de GarantíaExcepciones AÑO DE Servicio GratuitoDWE46102 EspecificacionesPage

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents