DeWalt DWE46102 instruction manual Safety Warnings Specific for Wire Brushing Operations

Page 8

English

Safety Warnings Specific for Wire Brushing Operations

a)Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.

b)If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work and centrifugal forces.

Additional Safety Rules for Grinders

WARNING: The grinding wheel or accessory may loosen during coast-down of the tool when shut off if rubber ring is missing or damaged. If grinding wheel or accessory loosens, it may dismount from the machine and may cause serious personal injury.

•Use of accessories not specified in this manual is not recommended and may be hazardous. Use of power boosters that would cause the tool to be driven at speeds greater than its rated speed constitutes misuse.

•Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

•Avoid bouncing the wheel or giving it rough treatment. If this occurs, stop the tool and inspect the wheel for cracks or flaws.

•Always handle and store wheels in a careful manner.

•Never cut into area that may contain electrical wiring or piping. Serious injury may result.

•Do not operate this tool for long periods of time. Vibration caused by the operating action of this tool may cause permanent

injury to fingers, hands, and arms. Use gloves to provide extra cushion, take frequent rest periods, and limit daily time of use.

•Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long hair can be caught in moving parts.

•An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

 

 

Volts

 

Total Length of Cord

 

 

 

 

in Feet (meters)

 

Ampere Rating

 

 

 

120V

25 (7.6)

50 (15.2)

100 (30.5)

150 (45.7)

 

 

 

 

240V

50 (15.2)

100 (30.5)

200 (61.0)

300 (91.4)

More

Not More

 

 

AWG

 

 

Than

Than

 

 

 

 

 

 

 

 

 

0

6

 

18

16

16

14

6

10

 

18

16

14

12

10

12

 

16

16

14

12

12

16

 

14

12

Not Recommended

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

•ANSI Z87.1 eye protection (CAN/CSA Z94.3),

•ANSI S12.6 (S3.19) hearing protection,

6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Guide D’UTILISATION Manual DE Instrucciones Page Definitions Safety Guidelines General Power Tool Safety WarningsWork Area Safety Electrical SafetyService Personal SafetyPower Tool USE and Care Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Sanding Operations Safety Warnings Specific for Polishing OperationsSafety Warnings Specific for Wire Brushing Operations Additional Safety Rules for GrindersSwitch Protection POWER-OFF Overload ProtectionSave These Instructions for Future USE ClutchComponents FIG Assembly and AdjustmentsMotor Become separated by more than 1/8 AccessoriesRotating the Gear Case FIg Mounting Guard Mounting and Removing GuardOperation Guards and FlangesSwitches Slider Switch FIGSpindle Lock FIG Mounting and Removing Hubbed Wheels FIGEdge Grinding with Grinding Wheels FIG Surface Grinding with Grinding Wheels FIGWheels Using Sanding Backing Pads FIG Surface Finishing with Sanding Flap Discs FIGMounting Sanding Backing Pads FIG Very Fine FinishingMounting and Using Wire Brushes and Wire Wheels Mounting Wire CUP Brushes and Wire WheelsUsing Wire CUP Brushes and Wire Wheels Wheel and the work surface with wireMounting and Using Cutting Type 1 Wheels Using Cutting Wheels FIGMounting Closed Type 1 Guard , 17 Mounting Cutting WheelsMaintenance CleaningThree Year Limited Warranty Addition to the warranty, Dewalt tools are covered by ourYear Free Service DAY Money Back GuaranteeSécurité EN Matière D’ÉLECTRICITÉ Définitions lignes directrices en Matière de sécuritéSécurité DU Lieu DE Travail Sécurité Personnelle Réparation Consignes DE Sécurité Pour Toutes LES OpérationsUtilisation ET Entretien D’UN Outil Électrique Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Dispositif E-CLUTCHMC Composant E-SWITCH Protectionmc Protection E-SWITCHConserver CES Consignes Pour Utilisation Ultérieure Moteur Description FIGAssemblage ET Réglages Complete Electronic Controlmc Contrôle Électronique CompletAccessoires Rotation du carter d’engrenage FIgMontage du dispositif de protection Fixation DE LA Poignée LatéraleDe travail voulue alors que le verrou est Désengagé. Le corps du capot devraitÊtre placé entre la broche et l’opérateur Pour maximiser la protection de ceEnclenché et que ce dernier est installé sur Pour retirer leReprendre Les étapes Capot ProtecteurFonctionnement Dispositifs de protection et bridesInterrupteurs Interrupteur Coulissant FIGDispositif DE Verrouillage DE LA Broche FIG Montage DE Meules Sans Moyeu FIGMeulage DE Bordure Avec DES Meules FIG Meulage DE Finition Avec DES Meules FIGSurface de la pièce, ce qui permet à Contact avec la surface de la pièce ÉlevéeUtilisation DES Patins DE Ponçage ET D’APPUI FIG Montage DES Patins D’APPUI ET DE Ponçage FIGSurface de travail Montage et utilisation de meules de coupe type Montage D’UN Dispositif DE Protection FerméMaximale à l’opérateur De serrage étant fermé’outil fonctionne à une vitesse élevée NettoyageUtilisation DES Meules DE Coupe FIG Réparations Garantie limitée de trois ansContrat D’ENTRETIEN Gratuit D’UN AN Garantie DE Remboursement DE 90 JoursSeguridad Eléctrica Definiciones Normas de seguridadSeguridad EN EL Área DE Trabajo Seguridad Personal USO Y Mantenimiento DE LA Herramienta EléctricaInstrucciones DE Seguridad Para Todas LAS Operaciones MantenimientoEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Protección Contra Sobrecarga POWER-OFF Guarde Estas Instrucciones Para Futuras ConsultasComponentes Fig Complete Electronic Control Control Electrónico CompletoComo girar la caja de engranajes FIg Ensamblado Y AjustesAccesorios Instalación DE LA Agarradera Lateral FIGInstalación del protector Protector tipo Brida de respaldo Disco con cubo tipoProtector tipo Disco de alambre Tuerca de fijación RoscadaColocado entre el eje y el operador, para proveer la máxima Protección al operadorFuncionamiento Protectores y bridasInterruptores Interruptor Deslizante FIGSuéltelo Bloqueo DEL EJE FIGMontaje Y Remoción DE Discos CON Cubo FIG Ensamblado DE Discos SIN Cubo FIGEsmerilado DE Superficies CON Discos Para Esmerilar FIG Discos DE 1/4Esmerilado DE Bordes Condiscos Para Esmerilar FIG Discos DE 1/8USO DE Almohadillas DE Respaldo Para Lijar Montaje DE LAS Almohadillas DE Respaldo Para Lijar FIGAcabado DE Superficies CON Discos Para Lijar Aproximadamente Mueva la herramienta constantemente Montaje y uso de cepillos de alambre y discos de alambreAplicarla a la superficie de trabajo Montaje y uso de los discos de corte Tipo Mantenga un ángulo de 5º a 10º entre la FIGMontaje DEL Protector Cerrado Tipo De trabajo deseada. El cuerpo delMantenimiento LimpiezaMontaje DE LOS Discos DE Corte USO DE Discos DE Corte FIGReparaciones Para Otras LocalidadesPóliza de Garantía Garantía limitada por tres añosExcepciones AÑO DE Servicio GratuitoEspecificaciones DWE46102Page

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents