DeWalt DWE46102 Surface Grinding with Grinding Wheels FIG, Edge Grinding with Grinding Wheels FIG

Page 15

recess is seated onto the flats of the spindle by pushing and twisting the flange before placing wheel.

2. Place wheel against the backing flange,

centering the wheel on the raised section

(pilot) of the backing flange.

FIG. 8

E

C

SURFACE GRINDING WITH GRINDING WHEELS (FIG. 9)

1.Allow the tool to reach full speed before touching the tool to the work surface.

2.Apply minimum pressure to the work surface, allowing the tool to operate at high speed. Grinding rate is greatest when the tool operates at high speed.

English

3. While depressing the spindle lock button,

thread the clamp nut (F) on spindle. If

the wheel you are installing is more than

1/8" (3.31 mm) thick, place the threaded

clamp nut on the spindle so that the

raised section (pilot) fits into the center of

the wheel. If the wheel you are installing

3. Maintain a 20˚ to 30˚ angle between the FIG. 9 tool and work surface.

4.

Continuously move the tool in a forward

 

F

and back motion to avoid creating

20˚–30˚

gouges in the work surface.

 

5.

Remove the tool from work surface before turning tool off. Allow

1/4" WHEELS

the tool to stop rotating before laying it down.

 

 

is 1/8" (3.31 mm) thick or less, place

 

the threaded clamp nut on the spindle

 

so that the raised section (pilot) is not

 

against the wheel.

4.

While depressing the spindle lock button,

 

tighten the clamp nut with a wrench.

5.

To remove the wheel, depress the spindle

 

lock button and loosen the threaded

 

clamp nut with a wrench.

NOTE: If the wheel spins after the clamp nut is tightened, check the orientation of the threaded clamp nut. If a thin wheel is installed with the pilot on the clamp nut against the wheel, it will spin because the height of the pilot prevents the clamp nut from holding the wheel.

(6.35 MM)

Clamp Nut

Backing Flange

1/8" WHEELS

(3.31 MM)

Clamp Nut

Backing Flange

EDGE GRINDING WITH GRINDING WHEELS (FIG. 10)

CAUTION: Wheels used for cutting and FIG. 10 edge grinding may break if they bend or twist

while the tool is being used to do cut-off work

or deep grinding. To reduce the risk of serious injury, limit the use of these wheels with a standard Type 27 guard to shallow cutting and notching (less than 1/2" in depth).

The open side of the guard must be positioned

away from the operator. For deeper cutting with a Type 1 cut-off wheel, use a closed, Type 1 guard. See the chart on page 10 for

more information. Type 1 guards are available at extra cost from your local dealer

or authorized service center.

1.Allow the tool to reach full speed before touching the tool to the work surface.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Guide D’UTILISATION Manual DE Instrucciones Page Electrical Safety Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Work Area SafetyPersonal Safety Power Tool USE and CareService Safety Instructions for ALL Operations Causes and Operator Prevention of Kickback Safety Warnings Specific for Polishing Operations Safety Warnings Specific for Sanding OperationsAdditional Safety Rules for Grinders Safety Warnings Specific for Wire Brushing OperationsClutch Switch ProtectionPOWER-OFF Overload Protection Save These Instructions for Future USEAssembly and Adjustments MotorComponents FIG Accessories Rotating the Gear Case FIgBecome separated by more than 1/8 Mounting and Removing Guard Mounting GuardGuards and Flanges OperationMounting and Removing Hubbed Wheels FIG SwitchesSlider Switch FIG Spindle Lock FIGSurface Grinding with Grinding Wheels FIG WheelsEdge Grinding with Grinding Wheels FIG Very Fine Finishing Using Sanding Backing Pads FIGSurface Finishing with Sanding Flap Discs FIG Mounting Sanding Backing Pads FIGWheel and the work surface with wire Mounting and Using Wire Brushes and Wire WheelsMounting Wire CUP Brushes and Wire Wheels Using Wire CUP Brushes and Wire WheelsMounting Cutting Wheels Mounting and Using Cutting Type 1 WheelsUsing Cutting Wheels FIG Mounting Closed Type 1 Guard , 17Addition to the warranty, Dewalt tools are covered by our MaintenanceCleaning Three Year Limited WarrantyDAY Money Back Guarantee Year Free ServiceDéfinitions lignes directrices en Matière de sécurité Sécurité DU Lieu DE TravailSécurité EN Matière D’ÉLECTRICITÉ Sécurité Personnelle Consignes DE Sécurité Pour Toutes LES Opérations Utilisation ET Entretien D’UN Outil ÉlectriqueRéparation Français Causes de l’effet de rebond et prévention par l’opérateur Français Règles additionnelles de sécurité propres aux meuleuses Calibres minimaux des rallonges Volts Composant E-SWITCH Protectionmc Protection E-SWITCH Conserver CES Consignes Pour Utilisation UltérieureDispositif E-CLUTCHMC Complete Electronic Controlmc Contrôle Électronique Complet MoteurDescription FIG Assemblage ET RéglagesFixation DE LA Poignée Latérale AccessoiresRotation du carter d’engrenage FIg Montage du dispositif de protectionPour maximiser la protection de ce De travail voulue alors que le verrou estDésengagé. Le corps du capot devrait Être placé entre la broche et l’opérateurCapot Protecteur Enclenché et que ce dernier est installé surPour retirer le Reprendre Les étapesInterrupteur Coulissant FIG FonctionnementDispositifs de protection et brides InterrupteursMontage DE Meules Sans Moyeu FIG Dispositif DE Verrouillage DE LA Broche FIGMeulage DE Finition Avec DES Meules FIG Surface de la pièce, ce qui permet àMeulage DE Bordure Avec DES Meules FIG Montage DES Patins D’APPUI ET DE Ponçage FIG Contact avec la surface de la pièceÉlevée Utilisation DES Patins DE Ponçage ET D’APPUI FIGSurface de travail De serrage étant fermé Montage et utilisation de meules de coupe typeMontage D’UN Dispositif DE Protection Fermé Maximale à l’opérateurNettoyage Utilisation DES Meules DE Coupe FIG’outil fonctionne à une vitesse élevée Garantie DE Remboursement DE 90 Jours RéparationsGarantie limitée de trois ans Contrat D’ENTRETIEN Gratuit D’UN ANDefiniciones Normas de seguridad Seguridad EN EL Área DE TrabajoSeguridad Eléctrica USO Y Mantenimiento DE LA Herramienta Eléctrica Seguridad PersonalMantenimiento Instrucciones DE Seguridad Para Todas LAS OperacionesEspañol Causas del retroceso y su prevención por parte del operador Español Normas de seguridad adicionales para esmeriladoras Desde Hasta Complete Electronic Control Control Electrónico Completo Protección Contra Sobrecarga POWER-OFFGuarde Estas Instrucciones Para Futuras Consultas Componentes FigInstalación DE LA Agarradera Lateral FIG Como girar la caja de engranajes FIgEnsamblado Y Ajustes AccesoriosTuerca de fijación Roscada Instalación del protectorProtector tipo Brida de respaldo Disco con cubo tipo Protector tipo Disco de alambreProtección al operador Colocado entre el eje y el operador, para proveer la máximaInterruptor Deslizante FIG FuncionamientoProtectores y bridas InterruptoresEnsamblado DE Discos SIN Cubo FIG SuélteloBloqueo DEL EJE FIG Montaje Y Remoción DE Discos CON Cubo FIGDiscos DE 1/8 Esmerilado DE Superficies CON Discos Para Esmerilar FIGDiscos DE 1/4 Esmerilado DE Bordes Condiscos Para Esmerilar FIGMontaje DE LAS Almohadillas DE Respaldo Para Lijar FIG Acabado DE Superficies CON Discos Para LijarUSO DE Almohadillas DE Respaldo Para Lijar Montaje y uso de cepillos de alambre y discos de alambre Aplicarla a la superficie de trabajoAproximadamente Mueva la herramienta constantemente De trabajo deseada. El cuerpo del Montaje y uso de los discos de corte TipoMantenga un ángulo de 5º a 10º entre la FIG Montaje DEL Protector Cerrado TipoUSO DE Discos DE Corte FIG MantenimientoLimpieza Montaje DE LOS Discos DE CortePara Otras Localidades ReparacionesAÑO DE Servicio Gratuito Póliza de GarantíaGarantía limitada por tres años ExcepcionesDWE46102 EspecificacionesPage

DWE46102 specifications

The DeWalt DWE46102 is a formidable addition to the world of power tools, designed to meet the needs of both professionals and DIY enthusiasts alike. As a high-performance corded grinder, it excels in various applications, including metal grinding, cutting, and concrete surface preparation.

One of the standout features of the DWE46102 is its powerful 13-amp motor. This robust motor delivers up to 10,500 RPM, providing users with the speed and efficiency required for demanding jobs. The grinder’s high-performance capabilities are further enhanced by its low-profile design, which allows for better maneuverability in tight spaces while ensuring maximum control during operation.

The DWE46102 is equipped with advanced technology aimed at maximizing user safety and comfort. Notably, it incorporates a Dust Ejection System, which is designed to prevent dust and debris from entering the motor, thereby extending its life and maintaining optimal performance. Additionally, the grinder features a lock-on switch, which enables continuous operation during prolonged use, reducing user fatigue.

Another impressive characteristic of the DWE46102 is its incorporated Active Vibration Control technology. This innovation significantly reduces vibration felt by the user, improving comfort and reducing fatigue, especially during long periods of operation. This is particularly beneficial in professional environments where tools are often used for extended durations.

Furthermore, the DeWalt DWE46102 is designed with durability in mind. Constructed with high-quality materials, it is built to withstand tough job site conditions. Its removable front guard facilitates easy tool-free adjustments and enhances versatility, allowing users to switch between cutting and grinding tasks smoothly.

The ergonomic design of the tool includes a comfortable grip and a side handle that can be positioned in multiple ways, providing better control and comfort for the operator. This attention to usability makes the DWE46102 not just efficient but also user-friendly.

In summary, the DeWalt DWE46102 is a powerful, versatile grinder that stands out due to its impressive motor, innovative technologies, and user-centric design. Whether you're working on metal, concrete, or other tough materials, this tool is engineered to deliver reliable performance, making it a valuable asset for anyone looking to tackle demanding projects.
Top Page Image Contents