Bosch Power Tools 4405 Installation And Removal Of The Blade, Larger or smaller than 10 diameter

Page 12
! WARNING
! WARNING

Assembly

Installation And Removal Of The Blade

Disconnect plug from power source before performing any assembly,

adjustment or repair to avoid possible injury.

1.Loosen rear cover plate screw one full turn. Do not completely remove screw.

2.Loosen front cover plate screw (approximately three full turns) until it clears the tab on the cover plate; but do not completely remove screw. Rotate coverplate counter-clockwise, exposing arbor bolt blade area.

3.Rotate the guard by hand to clear the blade. Let go of guard. Plastic will be held out of way by front screw.

4.Press and hold the arbor lock. The blade may need to be rotated for the arbor lock to catch. Use the blade wrench to remove the blade bolt by turning wrench clockwise. NOTE: The blade bolt has a left hand thread.

Lower Guard

Front Cover

Plate Screw

Turn Bolt This

Way to Loosen

Outer

Washer

Blade Bolt

Chip (Hex Cap)

Deflector

Figure 1. Blade Removal

5.Remove the blade bolt, arbor washer, outer washer and the blade. Inner washer does not need to be removed (Figure 2).

Outer Washer

Inner Washer

Arbor Washer

Blade Bolt

(Left Hand Thread)

Sawblade

Figure 2. Blade Hardware

6.To install the 10" blade, fit blade between the chip deflectors and onto arbor shaft (Figure 3). NOTE: Make sure the rotation arrow on the blade matches the clockwise rotation arrow on the lower guard.

 

Inner

 

Washer

 

Arbor Shaft

 

Chip

 

Deflector

Figure 3. Blade Installation

! WARNING

To avoid injury, do not use a blade

 

larger or smaller than 10" diameter

and 5/8" arbor.

7.Replace the outer washer, arbor washer, and tighten blade bolt finger tight counter-clockwise (see Figure 2). Press the arbor lock and tighten blade bolt securely using blade wrench, but do not overtighten.

8.Rotate cover plate clockwise to original position and tighten cover plate screws.

!WARNING Tighten the cover plate screws. Loose cover plate screw may

interfere with and hang-up lower blade guard. Never use saw without cover plate securely in place. Lower guard will not function properly.

9.Be sure the arbor lock is released so the blade turns freely.

After installing a new blade, make sure the blade does not interfere with the table insert at the 0° and 45° bevel posi-

tions. Lower the blade into the table slot and check for any contact with the base or turn table structure. If blade contacts base or table, seek authorized service at 1-877-BOSCH99.

10. Replace blade wrench in storage area on saw.

12.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 4405 Safety General Safety Rules For Bench Top ToolsSafety Rules For Miter Saws Tool Use and CareReaching with Your Hand Under a Coasting Blade is Dangerous Safety Table of Contents Electrical Requirements Electric BrakeSource outlet before making any adjustments Getting To Know Your Miter Saw16 35 31 Assembly Tools Needed For Assembly And AlignmentUnpacking And Checking Contents Attaching Miter Lock Knob Assembling Dust Elbow And Dust BagInstallation And Removal Of The Blade Larger or smaller than 10 diameterAdjustments Blade Alignment AdjustmentBlade Square To Table Blade Alignment CheckBlade 45 To Table Blade 45 To The Table 45º/33.9º Stop 45º Stop Screw Jam NutBlade 33.9 To Table Blade 33.9 To The TableMiter Scale Indicator Adjustment Fence Alignment AdjustmentBlade Square to Fence Fence Alignment CheckInstallation Mounting ApplicationsWorkbench Portable Mounting Using Clamps Stability Bar AdjustmentBasic Saw Operations Body and Hand PositionWorkpiece Support ClampsSwitch Activation Auxiliary FenceDetent Override Base ExtensionsSliding Fence Operating Sliding FenceSaw Operations Chop CutSlide Cut Miter Cut Bevel CutCompound Cuts Follow these instructions for making your bevel cutCutting Grooves Dado Cut Rough Cut Groove Depth Stop TabCutting Base Molding Cutting Crown MoldingCrown Molding Laying Flat on Table Follow these instructions for cutting crown molding52º Crown Molding Angled to Table and FenceSpecial Cuts Cutting Bowed MaterialCutting Round or Irregularly Shaped Material Maintenance and Lubrication Troubleshooting Troubleshooting Guide ElectricalTroubleshooting Guide General Slide Action Adjustment Adjusting Bevel Lock Lever TensionAccessories Various Blades Quick action Clamp BA160Page Seguridad Area de trabajoSeguridad personal Seguridad eléctricaUtilización y cuidado de las herramientas ServicioGroso Poner LA Mano Bajo UNA Hoja QUE AUN Gira POR Inercia Plos de estos agentes químicos son Plomo de pinturas a base de plomoPostería, y Arsénico y cromo de madera tratada químicamenteIndice Herramientas con aislamiento dobleCordones de extensión Ajuste de la barra de estabilidadFreno eléctrico Botón de Fijación en OFF apagado del interruptor Interruptor de encendidoMango con interruptor Cierre del eje portaherramientaPomo de fijación de inglete Indicador de la escala de ingletes/del ángulo de ingleteRetenes de inglete MesaEnsamblaje Herramientas necesarias para el ensamblaje y la alineaciónDesempaquetado y comprobación del contenido Sobre la tabla a lo largoInstalación del pomo de Fijación de inglete Ensamblaje del codo para polvo y la bolsa para polvoMente a presión, pintura que Instalación y remoción de la hoja Ajustes Hoja en ángulo recto con La mesaAjuste de la alineación de la hoja a Hoja a 45 respecto a la mesa Compruebe la alineación de la hoja aBaje el ensamblaje del cabezal. Fíjelo en su sitio Hoja Escuadra deHoja a 33.9 respecto a la mesa Tope de bisel deTope de 45/ 33.9º Tornillo de tope de Contratuerca Hoja en ángulo recto con el Tope-guía Ajuste del indicador De la escala de ingletesComprobación de la alineación del tope-guía Ajuste de la alineación del tope-guíaInstalación Aplicaciones de montajeBanco de trabajo Nunca lleve la sierra para cortar ingletes por el cordón deMontaje portátil usando abrazaderas Ajuste de la barra de estabilidadAfloje el pomo de la barra de estabilidad Barra de estabilidad Banco de trabajoOperaciones básicas de la sierra Posición del cuerpo y de las manosUso correcto Tas condiciones de corte. Si esto sucedeSoporte de la pieza de trabajo AbrazaderasAbrazadera Para la pieza De trabajoAgujeros Para abrazadera Activación del interruptor Ponentes interfiereRanura para la hoja Sobrecontrol del retén Extensiones de la baseTopes-guía deslizante Tope-guía deslizante Operaciones de la sierra Corte de troceadoCorte deslizante Siga estas instrucciones para hacer un corte de troceadoCorte a inglete Corte en biselSiga estas instrucciones para hacer un corte a inglete Cortes compuestos Corte de ranuras Corte de mortajas Corte las dos ranuras exterioresRanuras Corte de cincel Agarre estriado Corte de moldura de base Corte de moldura de techoMoldura de techo colocada horizontalmente sobre la mesa Tamaño MAX 10 1/4Siga estas instrucciones para cortar moldura de techo Bisel de 33.9Moldura de techo en ángulo respecto La mesa y al tope-guía Cortes especiales Corte de material arqueadoMantenimiento y lubricación Localización y reparación de averías Guía de localización y reparación de averías eléctricasGuía de localización y reparación de averías generales Ajuste de la acción De deslizamiento Repita los pasos 8-10 para el tornillo de ajuste CAccesorios Proporciona sujeción rápida de la pieza de trabajoNotas Sécurité Rité pour les outils d’établiZone de travail Sécurité électriqueUtilisation et entretien de l’outil RéparationSécurité Avertissement Table des matières Double isolationRallonges Remarque Plus le calibre est petit, plus le fil est grosSpécifications électriques Frein électriqueFamiliarisez-vous avec votre scie à onglet Guide fixe Inserts d’encoche Court-circuitage du cran d’arrêt d’ongletBouton de blocage d’onglet Indicateur d’angle d’onglet/échelle d’ongletAssemblage Outils nécessaires à l’assemblage et à l’alignementDéballage et vérification du contenu Téléphonez au 1-877-BOSCH99 si vous avez besoin dassistanceFixation du bouton de Blocage donglet Assemblage du coude de poussière et du sac à poussièreArbre Sac à Coude de Buse à PoussièrePose et dépose de la lame Réglages Lame d’équerre par rapport La tableVérification de lalignement de la lame à Réglage de lalignement de la lame àLame à 45 par rapport à la table Lame Équerre à CombinaisonButée 45/33,9º Vis d’arrêt N t r e écrou Lame à 33,9 par rapport à la table Vérification de lalignement de la lame à 33,9Réglage de lalignement de la lame à 33,9 Butée de biseau 33,9Lame d’équerre par Rapport au guide Vérification de lalignement du guideRéglage de lalignement du guide Vis à tête hexagonale Guide Unité de rails coulissantsInstallation Applications de montageÉtabli Droite de la scieMontage portatif à l’aide de serre-joints Réglage de la barre de stabilisationSurface de cramponnage Opérations de base de la scie Position du corps et des mainsSupport de l’ouvrage Serre-jointsIl peut Avoir Trous de Serre-jointserre-jointdouvrageActionnement de l’interrupteur Fente à lameGuide auxi Liaire Court-circuitage du cran d’arrêt Rallonges de baseGuide à glissière Opérations de la scie Coupe de fenteCoupe par glissement Suivez ces instructions pour pratiquer votre coupe de fenteCoupe à l’onglet Coupe en biseauOuvrage Crans d’arrêt Bouton deCoupes composées Angle deBiseau OngletCoupe de rainures Rainure coupée grossièrement Butée de profondeurCoupe de moulures de base Coupe de moulures en couronne100 Moulures en couronne reposant à plat sur la table 101102 Moulure en couronne à angle par rapport La table et au guideCoupes spéciales Coupe de matériaux courbésCoupe de matériaux ronds Ou de forme irrégulière 103Maintenance et lubrification Dépannage Guide de dépannage Électrique105 Guide de dépannage Généralités 106Réglage de laction coulissante 107Avant déviter tout risque de blessure Accessoires 108Remarques 109110 111 Limited Warranty of Bosch Portable and Benchtop Power Tools

4405 specifications

The Bosch Power Tools 4405 is a robust and versatile tool that caters to the needs of both professionals and DIY enthusiasts. With its compelling features and advanced technologies, the 4405 has established its position as a reliable choice for various cutting and drilling applications.

One of the standout features of the Bosch 4405 is its powerful motor. The tool is equipped with a 5.0 amp motor that delivers a no-load speed of up to 3,200 RPM. This powerful motor ensures swift and efficient performance, making it ideal for both heavy-duty tasks and intricate projects. The variable speed feature allows users to adjust the speed according to the material they are working on, providing greater control and flexibility.

The Bosch 4405 is also designed with precision in mind. It comes with a sturdy base that offers enhanced stability during operation, reducing vibrations and improving accuracy. The tool features a laser guide that aids in aligning cuts with precision, making it easier for users to achieve clean and accurate results. Additionally, its adjustable bevel cutting capability allows for angles up to 45 degrees, making it suitable for beveled cuts in various materials.

Durability is another characteristic that sets the Bosch 4405 apart. Constructed from high-quality materials, this power tool is designed to withstand the rigors of heavy use. The tool also features a dust blower that keeps the cutting line clear of debris, ensuring unobstructed visibility and enhancing safety during operation.

Safety features are paramount in the design of the Bosch 4405. It comes equipped with a blade guard that provides an additional layer of protection, minimizing the risk of accidental contact with the blade. The ergonomic handle is designed for comfort, reducing operator fatigue during extended use.

In summary, the Bosch Power Tools 4405 stands out for its powerful performance, precision cutting capabilities, durability, and safety features. Whether you are tackling a complex project or simple home repairs, the 4405 is a reliable tool that delivers impressive results, making it a must-have for any toolbox.
Top Page Image Contents