Bosch Power Tools 4405 manual Miter Cut, Bevel Cut

Page 25

Saw Operations

Miter Cut

•A miter cut is made at 0° bevel and any miter angle in the range from 50° left to 60° right.

•The miter scale is cast-in on the table for easy reading.

•Positive detents have been provided for fast and accurate mitering at 0°, 15°, 22.5°, and 45° left and right and 60° right.

•There are crown molding detents (left and right) at 31.6° (see Cutting Crown Molding for more information page 28).

•For off detent settings, use the detent override to lock out the detent.

•A miter cut can be made as either a chop cut or a slide cut depending on the width of the work- piece.

Follow these instructions for making your miter cut:

1.Loosen miter lock knob. Lift miter detent trigger and move the saw to the desired angle, using either the detents or the miter scale. Tighten miter lock knob (Figure 28).

2.Properly position workpiece. Make sure work piece is clamped firmly against the table and the fence.

!WARNING Use clamping position that does not interfere with operation. Before

switching on, lower head assembly to make sure clamp clears guard and head assembly.

3.Follow procedures for either chop cut or slide cut (see page 24).

4.Wait until blade comes to a complete stop before returning head assembly to the raised position and/or removing workpiece.

Workpiece

Clamp

Workpiece

Detents Miter Scale Miter Lock

Knob

Figure 28. Miter Cut

Bevel Cut

• There is a positive crown molding bevel stop at

33.9°. Disengage this stop unless using. (See

• A bevel cut is made at 0° miter and any bevel

Cutting Crown Molding for details.)

angle in the range of 0° to 45°.

 

• There are factory set bevel stops at 0° and 45°. (See

• A bevel cut can be made as either a chop cut or

a slide cut depending on the width of the work-

Adjustment section if adjustments are required.)

piece.

• The bevel scale faces the operator for easy reading.

• Use sliding fence and work supports as appropri-

 

ate. (See Sliding Base/Fence Extension page 23.)

 

 

 

25.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 4405 General Safety Rules For Bench Top Tools SafetyTool Use and Care Safety Rules For Miter SawsReaching with Your Hand Under a Coasting Blade is Dangerous Safety Table of Contents Electric Brake Electrical RequirementsGetting To Know Your Miter Saw Source outlet before making any adjustments16 35 31 Tools Needed For Assembly And Alignment AssemblyUnpacking And Checking Contents Assembling Dust Elbow And Dust Bag Attaching Miter Lock KnobLarger or smaller than 10 diameter Installation And Removal Of The BladeBlade Alignment Adjustment AdjustmentsBlade Square To Table Blade Alignment CheckBlade 45 To The Table 45º/33.9º Stop 45º Stop Screw Jam Nut Blade 45 To TableBlade 33.9 To The Table Blade 33.9 To TableFence Alignment Adjustment Miter Scale Indicator AdjustmentBlade Square to Fence Fence Alignment CheckMounting Applications InstallationWorkbench Stability Bar Adjustment Portable Mounting Using ClampsBody and Hand Position Basic Saw OperationsClamps Workpiece SupportAuxiliary Fence Switch ActivationBase Extensions Detent OverrideOperating Sliding Fence Sliding FenceChop Cut Saw OperationsSlide Cut Bevel Cut Miter CutFollow these instructions for making your bevel cut Compound CutsRough Cut Groove Depth Stop Tab Cutting Grooves Dado CutCutting Crown Molding Cutting Base MoldingFollow these instructions for cutting crown molding Crown Molding Laying Flat on TableCrown Molding Angled to Table and Fence 52ºCutting Bowed Material Special CutsCutting Round or Irregularly Shaped Material Maintenance and Lubrication Troubleshooting Guide Electrical TroubleshootingTroubleshooting Guide General Adjusting Bevel Lock Lever Tension Slide Action AdjustmentVarious Blades Quick action Clamp BA160 AccessoriesPage Area de trabajo SeguridadSeguridad personal Seguridad eléctricaServicio Utilización y cuidado de las herramientasGroso Poner LA Mano Bajo UNA Hoja QUE AUN Gira POR Inercia Plomo de pinturas a base de plomo Plos de estos agentes químicos sonPostería, y Arsénico y cromo de madera tratada químicamenteHerramientas con aislamiento doble IndiceCordones de extensión Ajuste de la barra de estabilidadFreno eléctrico Interruptor de encendido Botón de Fijación en OFF apagado del interruptorMango con interruptor Cierre del eje portaherramientaIndicador de la escala de ingletes/del ángulo de inglete Pomo de fijación de ingleteRetenes de inglete MesaHerramientas necesarias para el ensamblaje y la alineación EnsamblajeDesempaquetado y comprobación del contenido Sobre la tabla a lo largoEnsamblaje del codo para polvo y la bolsa para polvo Instalación del pomo de Fijación de ingleteMente a presión, pintura que Instalación y remoción de la hoja Hoja en ángulo recto con La mesa AjustesAjuste de la alineación de la hoja a Compruebe la alineación de la hoja a Hoja a 45 respecto a la mesaBaje el ensamblaje del cabezal. Fíjelo en su sitio Hoja Escuadra deTope de bisel de Hoja a 33.9 respecto a la mesaTope de 45/ 33.9º Tornillo de tope de Contratuerca Ajuste del indicador De la escala de ingletes Hoja en ángulo recto con el Tope-guíaComprobación de la alineación del tope-guía Ajuste de la alineación del tope-guíaAplicaciones de montaje InstalaciónBanco de trabajo Nunca lleve la sierra para cortar ingletes por el cordón deAjuste de la barra de estabilidad Montaje portátil usando abrazaderasAfloje el pomo de la barra de estabilidad Barra de estabilidad Banco de trabajoPosición del cuerpo y de las manos Operaciones básicas de la sierraUso correcto Tas condiciones de corte. Si esto sucedeAbrazaderas Soporte de la pieza de trabajoAbrazadera Para la pieza De trabajoAgujeros Para abrazadera Ponentes interfiere Activación del interruptorRanura para la hoja Extensiones de la base Sobrecontrol del reténTopes-guía deslizante Tope-guía deslizante Corte de troceado Operaciones de la sierraCorte deslizante Siga estas instrucciones para hacer un corte de troceadoCorte en bisel Corte a ingleteSiga estas instrucciones para hacer un corte a inglete Cortes compuestos Corte las dos ranuras exteriores Corte de ranuras Corte de mortajasRanuras Corte de cincel Agarre estriado Corte de moldura de techo Corte de moldura de baseTamaño MAX 10 1/4 Moldura de techo colocada horizontalmente sobre la mesaSiga estas instrucciones para cortar moldura de techo Bisel de 33.9Moldura de techo en ángulo respecto La mesa y al tope-guía Corte de material arqueado Cortes especialesMantenimiento y lubricación Guía de localización y reparación de averías eléctricas Localización y reparación de averíasGuía de localización y reparación de averías generales Repita los pasos 8-10 para el tornillo de ajuste C Ajuste de la acción De deslizamientoProporciona sujeción rápida de la pieza de trabajo AccesoriosNotas Rité pour les outils d’établi SécuritéZone de travail Sécurité électriqueRéparation Utilisation et entretien de l’outilSécurité Avertissement Double isolation Table des matièresRallonges Remarque Plus le calibre est petit, plus le fil est grosFrein électrique Spécifications électriquesFamiliarisez-vous avec votre scie à onglet Inserts d’encoche Court-circuitage du cran d’arrêt d’onglet Guide fixeBouton de blocage d’onglet Indicateur d’angle d’onglet/échelle d’ongletOutils nécessaires à l’assemblage et à l’alignement AssemblageDéballage et vérification du contenu Téléphonez au 1-877-BOSCH99 si vous avez besoin dassistanceAssemblage du coude de poussière et du sac à poussière Fixation du bouton de Blocage dongletArbre Sac à Coude de Buse à PoussièrePose et dépose de la lame Lame d’équerre par rapport La table RéglagesVérification de lalignement de la lame à Réglage de lalignement de la lame àLame Équerre à Combinaison Lame à 45 par rapport à la tableButée 45/33,9º Vis d’arrêt N t r e écrou Vérification de lalignement de la lame à 33,9 Lame à 33,9 par rapport à la tableRéglage de lalignement de la lame à 33,9 Butée de biseau 33,9Vérification de lalignement du guide Lame d’équerre par Rapport au guideRéglage de lalignement du guide Vis à tête hexagonale Guide Unité de rails coulissantsApplications de montage InstallationÉtabli Droite de la scieRéglage de la barre de stabilisation Montage portatif à l’aide de serre-jointsSurface de cramponnage Position du corps et des mains Opérations de base de la scieSerre-joints Support de l’ouvrageIl peut Avoir Trous de Serre-jointserre-jointdouvrageFente à lame Actionnement de l’interrupteurGuide auxi Liaire Rallonges de base Court-circuitage du cran d’arrêtGuide à glissière Coupe de fente Opérations de la scieCoupe par glissement Suivez ces instructions pour pratiquer votre coupe de fenteCoupe en biseau Coupe à l’ongletOuvrage Crans d’arrêt Bouton deAngle de Coupes composéesBiseau OngletRainure coupée grossièrement Butée de profondeur Coupe de rainuresCoupe de moulures en couronne Coupe de moulures de base100 101 Moulures en couronne reposant à plat sur la tableMoulure en couronne à angle par rapport La table et au guide 102Coupe de matériaux courbés Coupes spécialesCoupe de matériaux ronds Ou de forme irrégulière 103Maintenance et lubrification Guide de dépannage Électrique Dépannage105 106 Guide de dépannage Généralités107 Réglage de laction coulissanteAvant déviter tout risque de blessure 108 Accessoires109 Remarques110 111 Limited Warranty of Bosch Portable and Benchtop Power Tools

4405 specifications

The Bosch Power Tools 4405 is a robust and versatile tool that caters to the needs of both professionals and DIY enthusiasts. With its compelling features and advanced technologies, the 4405 has established its position as a reliable choice for various cutting and drilling applications.

One of the standout features of the Bosch 4405 is its powerful motor. The tool is equipped with a 5.0 amp motor that delivers a no-load speed of up to 3,200 RPM. This powerful motor ensures swift and efficient performance, making it ideal for both heavy-duty tasks and intricate projects. The variable speed feature allows users to adjust the speed according to the material they are working on, providing greater control and flexibility.

The Bosch 4405 is also designed with precision in mind. It comes with a sturdy base that offers enhanced stability during operation, reducing vibrations and improving accuracy. The tool features a laser guide that aids in aligning cuts with precision, making it easier for users to achieve clean and accurate results. Additionally, its adjustable bevel cutting capability allows for angles up to 45 degrees, making it suitable for beveled cuts in various materials.

Durability is another characteristic that sets the Bosch 4405 apart. Constructed from high-quality materials, this power tool is designed to withstand the rigors of heavy use. The tool also features a dust blower that keeps the cutting line clear of debris, ensuring unobstructed visibility and enhancing safety during operation.

Safety features are paramount in the design of the Bosch 4405. It comes equipped with a blade guard that provides an additional layer of protection, minimizing the risk of accidental contact with the blade. The ergonomic handle is designed for comfort, reducing operator fatigue during extended use.

In summary, the Bosch Power Tools 4405 stands out for its powerful performance, precision cutting capabilities, durability, and safety features. Whether you are tackling a complex project or simple home repairs, the 4405 is a reliable tool that delivers impressive results, making it a must-have for any toolbox.
Top Page Image Contents