Bosch Power Tools 4405 manual Installation, Mounting Applications, Workbench

Page 17

Installation

!WARNING To avoid injury always observe the following:

●Unplug electric cord. Before transporting the saw, rotate head assembly to 45° right miter, lock into detent, pull the head assembly com- pletely forward toward you, tighten the slide rail lock knob and lock the head assembly in the lowered position.

●To avoid back injury, hold the tool close to your body when lifting. Bend your knees so you can lift with your legs, not your back. Lift by using the cast-in carry handles at each side of the bot- tom of the base or the carry handle.

●Never carry the tool by the slide rails, this may cause blade misalignment.

●Never carry the miter saw by the power cord or the operational handle. Attempting to lift or carry the tool by the power cord will damage the insulation and the wire connections result- ing in electric shock or fire.

●Observe the position of the saw. People standing behind it could be injured by thrown debris.

●Place the saw on a firm, level surface where there is plenty of room for handling and proper- ly supporting the workpiece.

●Bolt, screw, nail or clamp the saw to its support surface.

! CAUTION

Be careful not to over drive nail

 

or over torque the bolt when

 

attaching to support surface. This could crack foot or damage base.

Mounting Applications

Workbench

Mount the saw using either the four bolt holes (7/16") or the four screw holes (1/4”) to the workbench (Figure 16). Check for clearance to the left and right of the saw.

Bolt Holes

Screw Holes

Screw Holes

Bolt Holes

Figure 16. Workbench Mounting

1.Each of the four mounting holes should be bolt- ed securely using 3/8" bolts, lock washers, and hex nuts (not included).

2.Locate and mark where the saw is to be mount- ed.

3.Drill four (4) 3/8" diameter holes through work- bench.

4.Place the slide compound miter saw on the workbench aligning holes in base with holes drilled in workbench. Install bolts, lock wash- ers and hex nuts.

Supporting surface where saw is to be mounted should be examined carefully after mounting to ensure that no movement can occur during use. If any tipping or walking of the saw is noted, check your mounting to the workbench or stand, and make nec- essary adjustments before operating the slide com- pound miter saw (see Stability Bar Adjustment on page 18).

17.

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 4405 General Safety Rules For Bench Top Tools SafetyTool Use and Care Safety Rules For Miter SawsReaching with Your Hand Under a Coasting Blade is Dangerous Safety Table of Contents Electric Brake Electrical RequirementsGetting To Know Your Miter Saw Source outlet before making any adjustments16 35 31 Unpacking And Checking Contents AssemblyTools Needed For Assembly And Alignment Assembling Dust Elbow And Dust Bag Attaching Miter Lock KnobLarger or smaller than 10 diameter Installation And Removal Of The BladeBlade Alignment Adjustment AdjustmentsBlade Square To Table Blade Alignment CheckBlade 45 To The Table 45º/33.9º Stop 45º Stop Screw Jam Nut Blade 45 To TableBlade 33.9 To The Table Blade 33.9 To TableFence Alignment Adjustment Miter Scale Indicator AdjustmentBlade Square to Fence Fence Alignment CheckWorkbench InstallationMounting Applications Stability Bar Adjustment Portable Mounting Using ClampsBody and Hand Position Basic Saw OperationsClamps Workpiece SupportAuxiliary Fence Switch ActivationBase Extensions Detent OverrideOperating Sliding Fence Sliding FenceSlide Cut Saw OperationsChop Cut Bevel Cut Miter CutFollow these instructions for making your bevel cut Compound CutsRough Cut Groove Depth Stop Tab Cutting Grooves Dado CutCutting Crown Molding Cutting Base MoldingFollow these instructions for cutting crown molding Crown Molding Laying Flat on TableCrown Molding Angled to Table and Fence 52ºCutting Round or Irregularly Shaped Material Special CutsCutting Bowed Material Maintenance and Lubrication Troubleshooting Guide Electrical TroubleshootingTroubleshooting Guide General Adjusting Bevel Lock Lever Tension Slide Action AdjustmentVarious Blades Quick action Clamp BA160 AccessoriesPage Area de trabajo SeguridadSeguridad personal Seguridad eléctricaServicio Utilización y cuidado de las herramientasGroso Poner LA Mano Bajo UNA Hoja QUE AUN Gira POR Inercia Plomo de pinturas a base de plomo Plos de estos agentes químicos sonPostería, y Arsénico y cromo de madera tratada químicamenteHerramientas con aislamiento doble IndiceCordones de extensión Ajuste de la barra de estabilidadFreno eléctrico Interruptor de encendido Botón de Fijación en OFF apagado del interruptorMango con interruptor Cierre del eje portaherramientaIndicador de la escala de ingletes/del ángulo de inglete Pomo de fijación de ingleteRetenes de inglete MesaHerramientas necesarias para el ensamblaje y la alineación EnsamblajeDesempaquetado y comprobación del contenido Sobre la tabla a lo largoMente a presión, pintura que Instalación del pomo de Fijación de ingleteEnsamblaje del codo para polvo y la bolsa para polvo Instalación y remoción de la hoja Ajuste de la alineación de la hoja a AjustesHoja en ángulo recto con La mesa Compruebe la alineación de la hoja a Hoja a 45 respecto a la mesaBaje el ensamblaje del cabezal. Fíjelo en su sitio Hoja Escuadra deTope de 45/ 33.9º Tornillo de tope de Contratuerca Hoja a 33.9 respecto a la mesaTope de bisel de Ajuste del indicador De la escala de ingletes Hoja en ángulo recto con el Tope-guíaComprobación de la alineación del tope-guía Ajuste de la alineación del tope-guíaAplicaciones de montaje InstalaciónBanco de trabajo Nunca lleve la sierra para cortar ingletes por el cordón deAjuste de la barra de estabilidad Montaje portátil usando abrazaderasAfloje el pomo de la barra de estabilidad Barra de estabilidad Banco de trabajoPosición del cuerpo y de las manos Operaciones básicas de la sierraUso correcto Tas condiciones de corte. Si esto sucedeAbrazadera Para la pieza De trabajoAgujeros Para abrazadera Soporte de la pieza de trabajoAbrazaderas Ranura para la hoja Activación del interruptorPonentes interfiere Extensiones de la base Sobrecontrol del reténTopes-guía deslizante Tope-guía deslizante Corte de troceado Operaciones de la sierraCorte deslizante Siga estas instrucciones para hacer un corte de troceadoSiga estas instrucciones para hacer un corte a inglete Corte a ingleteCorte en bisel Cortes compuestos Ranuras Corte de cincel Agarre estriado Corte de ranuras Corte de mortajasCorte las dos ranuras exteriores Corte de moldura de techo Corte de moldura de baseTamaño MAX 10 1/4 Moldura de techo colocada horizontalmente sobre la mesaSiga estas instrucciones para cortar moldura de techo Bisel de 33.9Moldura de techo en ángulo respecto La mesa y al tope-guía Corte de material arqueado Cortes especialesMantenimiento y lubricación Guía de localización y reparación de averías eléctricas Localización y reparación de averíasGuía de localización y reparación de averías generales Repita los pasos 8-10 para el tornillo de ajuste C Ajuste de la acción De deslizamientoProporciona sujeción rápida de la pieza de trabajo AccesoriosNotas Rité pour les outils d’établi SécuritéZone de travail Sécurité électriqueRéparation Utilisation et entretien de l’outilSécurité Avertissement Double isolation Table des matièresRallonges Remarque Plus le calibre est petit, plus le fil est grosFrein électrique Spécifications électriquesFamiliarisez-vous avec votre scie à onglet Inserts d’encoche Court-circuitage du cran d’arrêt d’onglet Guide fixeBouton de blocage d’onglet Indicateur d’angle d’onglet/échelle d’ongletOutils nécessaires à l’assemblage et à l’alignement AssemblageDéballage et vérification du contenu Téléphonez au 1-877-BOSCH99 si vous avez besoin dassistanceAssemblage du coude de poussière et du sac à poussière Fixation du bouton de Blocage dongletArbre Sac à Coude de Buse à PoussièrePose et dépose de la lame Lame d’équerre par rapport La table RéglagesVérification de lalignement de la lame à Réglage de lalignement de la lame àButée 45/33,9º Vis d’arrêt N t r e écrou Lame à 45 par rapport à la tableLame Équerre à Combinaison Vérification de lalignement de la lame à 33,9 Lame à 33,9 par rapport à la tableRéglage de lalignement de la lame à 33,9 Butée de biseau 33,9Vérification de lalignement du guide Lame d’équerre par Rapport au guideRéglage de lalignement du guide Vis à tête hexagonale Guide Unité de rails coulissantsApplications de montage InstallationÉtabli Droite de la scieSurface de cramponnage Montage portatif à l’aide de serre-jointsRéglage de la barre de stabilisation Position du corps et des mains Opérations de base de la scieSerre-joints Support de l’ouvrageIl peut Avoir Trous de Serre-jointserre-jointdouvrageGuide auxi Liaire Actionnement de l’interrupteurFente à lame Rallonges de base Court-circuitage du cran d’arrêtGuide à glissière Coupe de fente Opérations de la scieCoupe par glissement Suivez ces instructions pour pratiquer votre coupe de fenteCoupe en biseau Coupe à l’ongletOuvrage Crans d’arrêt Bouton deAngle de Coupes composéesBiseau OngletRainure coupée grossièrement Butée de profondeur Coupe de rainures100 Coupe de moulures de baseCoupe de moulures en couronne 101 Moulures en couronne reposant à plat sur la tableMoulure en couronne à angle par rapport La table et au guide 102Coupe de matériaux courbés Coupes spécialesCoupe de matériaux ronds Ou de forme irrégulière 103Maintenance et lubrification 105 DépannageGuide de dépannage Électrique 106 Guide de dépannage GénéralitésAvant déviter tout risque de blessure Réglage de laction coulissante107 108 Accessoires109 Remarques110 111 Limited Warranty of Bosch Portable and Benchtop Power Tools

4405 specifications

The Bosch Power Tools 4405 is a robust and versatile tool that caters to the needs of both professionals and DIY enthusiasts. With its compelling features and advanced technologies, the 4405 has established its position as a reliable choice for various cutting and drilling applications.

One of the standout features of the Bosch 4405 is its powerful motor. The tool is equipped with a 5.0 amp motor that delivers a no-load speed of up to 3,200 RPM. This powerful motor ensures swift and efficient performance, making it ideal for both heavy-duty tasks and intricate projects. The variable speed feature allows users to adjust the speed according to the material they are working on, providing greater control and flexibility.

The Bosch 4405 is also designed with precision in mind. It comes with a sturdy base that offers enhanced stability during operation, reducing vibrations and improving accuracy. The tool features a laser guide that aids in aligning cuts with precision, making it easier for users to achieve clean and accurate results. Additionally, its adjustable bevel cutting capability allows for angles up to 45 degrees, making it suitable for beveled cuts in various materials.

Durability is another characteristic that sets the Bosch 4405 apart. Constructed from high-quality materials, this power tool is designed to withstand the rigors of heavy use. The tool also features a dust blower that keeps the cutting line clear of debris, ensuring unobstructed visibility and enhancing safety during operation.

Safety features are paramount in the design of the Bosch 4405. It comes equipped with a blade guard that provides an additional layer of protection, minimizing the risk of accidental contact with the blade. The ergonomic handle is designed for comfort, reducing operator fatigue during extended use.

In summary, the Bosch Power Tools 4405 stands out for its powerful performance, precision cutting capabilities, durability, and safety features. Whether you are tackling a complex project or simple home repairs, the 4405 is a reliable tool that delivers impressive results, making it a must-have for any toolbox.
Top Page Image Contents