Black & Decker JS680V Setting the desired cutting mode Smart Select figure D, Icon

Page 7

Setting the desired cutting mode (Smart Select )(figure D)

	To select the proper speed and orbital action
	To select the proper speed and orbital action	D
	for the type of material that you are cutting,	D
	for the type of material that you are cutting,
	follow the steps below:

Step 1 - Turn the dial (10) as shown in figure D to the appropriate icon. Refer to the chart below for descriptions of the 7 different positions.

Step 2 - Insert the proper blade based on the chart.

Step 3 - Perform the cut.

	NOTE: These settings are initial
	recommendations. Your application may
	work best with different settings. Test
	these positions on similar material prior to
	making finished cut and adjust selections	10
	for desired results.	10
	for desired results.

How to use the Smart SelectTM dial

This tool is equipped with a unique Smart SelectTM Dial to set the speed and the orbital blade action for various cutting applications. To select the optimum speed and orbital blade action for the type of material being cut, turn the dial as shown in the table below.

	Icon
3200/min
3200/min
3000/min
3000/min
2300/min	PVC
	PVC
1700/min

Application	Speed/Orbit	Blade Type
Kitchen work surfaces,	Fast speed,	General wood
work tops, laminate	No orbit
board
Scrolling/curves/	Fast speed,	Scrolling wood
craftwork, hardwoods,	No orbit	General wood
decking, flooring
Plywood and wood	Fast speed,	General wood
panels	medium orbit
General timber, soft	Fast speed,	General wood
wood, fast rip cutting	max orbit
Plastics, Perspex, PVC	Medium speed,	General purpose
	medium orbit
Sheet metal tin plate,	Low speed,	Metal or ceramic or
ceramic tile, fiberglass	no orbit	fiberglass blade
sheet
Slow speed,	Slow speed,	Choose the correct
precision start	no orbit	blade for the application

7

Image 7

Contents VEA EL ESPAñOL EN LA Contraportada JS680VWork Area Safety Safety Guidelines DefinitionsSpecific Safety Rules Symbols Use of Extension Cords Functional DescriptionMotor To set the bevel angle Blade Installation figure aAdjusting the shoe plate for bevel cuts figure B & C OperationIcon Setting the desired cutting mode Smart Select figure DApplication Speed/Orbit Blade Type To use the UV light Using the UV light figure G & HBlade storage figure E To open the storage doorSawing metal Hints for optimum useHighlighter Pen Storage figure Sawing laminatesTroubleshooting Problem Possible Cause Possible Solution Accessories TroubleshootingProblem Possible Cause Possible Solution MaintenanceMode d’emploi Lignes directrices en matière de sécurité définitions Règles de sécurité spécifiques · le plomb dans les peintures à base de plomb Description fonctionnelle SymbolesInsertion de la lame fig. a FonctionnementRéglage de l’angle de biseau Réglage du mode de coupe voulu Smart Select figure DPour régler la plaque de la semelle pour des Coupes droites Icône Application Vitesse/orbite Type de lame Utilisation du cadran Smart SelectTMMise en marche et arrêt Rangement de la lame figure EOuverture de la porte du compartiment de Rangement Les lames sont tenues en position par un AimantCoupe du métal Rangement du crayon marqueur figureRaccordement d’un aspirateur à l’outil Conseils pratiques pour un usage optimal Coupe de lamellésDépannage Problème Cause possible Solution possibleSciage en long et coupe circulaire figures J et K Entretien Manual DE Instrucciones Pautas DE SEGURIDAD/DEFINICIONES Esto garantizará la seguridad de la herramienta eléctrica Normas de seguridad específicas Símbolos Descripción de las funcionesInstalación de la hoja figura a Guarde Estas Instrucciones FuncionamientoDe corte deseado Smart Select figura Configuración delPara establecer el ángulo de bisel Para fijar la placa De la zapata para cortes RectosAlmacenamiento de la hoja fig. E Cómo utilizar el dial Smart SelectTMIcono Aplicación Velocidad/Órbita Tipo de hojaUso de la luz UV figuras G y H Encendido y apagadoPara usar la luz UV Aserrado en metal Almacenamiento del bolígrafo resaltador figuraCómo conectar la aspiradora a la herramienta Para aserrar laminadosProblema Causa posible Solución posible Detección de problemasMantenimiento MERIDA, YUC Calle 63 #459-A 999 928 5038 Col. Centro GUADALAJARA, JAL Av. La Paz #1779 33 3825SAN Luis POTOSI, SLP Av. Universidad 1525 444 814