Black & Decker JS680V Hints for optimum use, Highlighter Pen Storage figure, Sawing laminates

Page 9

-Switch the UV light (13) on by pressing the button (12).

-To switch the UV light (13) off, press the button (12) again.

-Position the jig saw over the cutting line (19).

Viewing from directly above the jig saw, the line of cut will be illuminated (20) by the UV light (13) and can be easily followed.

H

12

20

1913 20

13

Highlighter Pen Storage (figure I)
- The highlighter marking pen (14) stores in
- The highlighter marking pen (14) stores in	I		15
the pen holder (15).	I	21	15
- The pen holder (15) can be opened and		21
attached anywhere on the cord (21) as shown
in figure I.
- To move the pen holder, unlock the hinge
and open the holder.
- Remove from cord and place anywhere up
or down the cord.
NOTE: Should you need to replace the
highlighter marking pen (14) it can be
replaced with a standard yellow highlighter	14
found at office supply stores (fine tip	14
recommended).

Connecting a vacuum cleaner to the tool A hose adapter (not supplied) is available at extra cost through your nearest Black

& Decker service center. Insert the hose adapter into the opening at the back of the saw. Connect a vacuum cleaner hose (not supplied) to the hose adapter.

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to the shoe plate.

- Use a fine-tooth saw blade.

- Saw from the back surface of the workpiece.

- To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the workpiece and saw through this sandwich.

Sawing metal

- Be aware that sawing metal takes much more time than sawing wood. - Use a saw blade suitable for sawing metal.

- When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece and cut through this sandwich.

- Spread a film of oil along the intended line of cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred.

WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings are hot and may cause a fire.

9

Image 9

Contents VEA EL ESPAñOL EN LA Contraportada JS680VWork Area Safety Safety Guidelines DefinitionsSpecific Safety Rules Symbols Functional Description Use of Extension CordsMotor Adjusting the shoe plate for bevel cuts figure B & C Blade Installation figure aOperation To set the bevel angleSetting the desired cutting mode Smart Select figure D IconApplication Speed/Orbit Blade Type Blade storage figure E Using the UV light figure G & HTo open the storage door To use the UV lightHighlighter Pen Storage figure Hints for optimum useSawing laminates Sawing metalTroubleshooting Problem Possible Cause Possible Solution Problem Possible Cause Possible Solution TroubleshootingMaintenance AccessoriesMode d’emploi Lignes directrices en matière de sécurité définitions Règles de sécurité spécifiques · le plomb dans les peintures à base de plomb Description fonctionnelle SymbolesInsertion de la lame fig. a FonctionnementRéglage du mode de coupe voulu Smart Select figure D Réglage de l’angle de biseauPour régler la plaque de la semelle pour des Coupes droites Icône Application Vitesse/orbite Type de lame Utilisation du cadran Smart SelectTMOuverture de la porte du compartiment de Rangement Rangement de la lame figure ELes lames sont tenues en position par un Aimant Mise en marche et arrêtRaccordement d’un aspirateur à l’outil Rangement du crayon marqueur figureConseils pratiques pour un usage optimal Coupe de lamellés Coupe du métalProblème Cause possible Solution possible DépannageSciage en long et coupe circulaire figures J et K Entretien Manual DE Instrucciones Pautas DE SEGURIDAD/DEFINICIONES Esto garantizará la seguridad de la herramienta eléctrica Normas de seguridad específicas Símbolos Descripción de las funcionesInstalación de la hoja figura a Guarde Estas Instrucciones FuncionamientoPara establecer el ángulo de bisel Configuración delPara fijar la placa De la zapata para cortes Rectos De corte deseado Smart Select figuraIcono Cómo utilizar el dial Smart SelectTMAplicación Velocidad/Órbita Tipo de hoja Almacenamiento de la hoja fig. EEncendido y apagado Uso de la luz UV figuras G y HPara usar la luz UV Cómo conectar la aspiradora a la herramienta Almacenamiento del bolígrafo resaltador figuraPara aserrar laminados Aserrado en metalProblema Causa posible Solución posible Detección de problemasMantenimiento GUADALAJARA, JAL Av. La Paz #1779 33 3825 MERIDA, YUC Calle 63 #459-A 999 928 5038 Col. CentroSAN Luis POTOSI, SLP Av. Universidad 1525 444 814