Shindaiwa 4 Cycle Diesel Engine specifications 『Dual 』, 35-280A45-310A φ2.0-φ6.0

Page 20

welding output selector switch (『ECO』,『Single』and『Dual』). Welding Current Adjustable Range

	Selector Position	Current Adjustable Range	Welding Rod

Single	ECO	30-160A	φ2.0-4.0

	Single Use	85-310A	φ2.6-6.0

Dual	Dual Use	45-160A	φ2.0-4.0

After the engine is started (Refer to No. 7.1 Initializing/Preparation), operate as per the proce-

dures in the following table.	CURRENT ADJUSTMENT	CURRENT ADJUSTMENT
	DIAL A	DIAL B

		OUTPUT SELECTOR
		SWITCH	WELDING OUTPUT
	WELDING OUTPUT		WELDING OUTPUT
	WELDING OUTPUT		TERMINAL B
	TERMINAL A
	Welding Operation Procedure

Procedure	Operation	ECO (Single)		Single Welding	Dual Welding
		Welding Rod		Welding Rod	Welding Rod
		φ2.0-φ4.0		φ2.6-φ6.0	φ2.0-φ4.0

①	Selector	『ECO』		『SINGLE』	『DUAL』

②	Current	Current Adjust.		Current Adjust.	Current Adjust.
	Adjustment	Dial A		Dial A	Dial A + B

8-5.2 DGW311L

①Start the engine. (Refer to No. 7.1 Initializing/Preparation)

② Adjust the current by the current adjustment dial.

Welding Current Adjustable Range

Current Adjustable Range

50Hz60Hz Welding Rod

-(W)380A,-(W)400A,-(W)415A -(W)220B

35-280A45-310A φ2.0-φ6.0

9.Generator Operation 9-1 Output Range

9-1.1 DGW311DM-(W)220B, DGW311L-(W)220B 9-1.1.1 3-Phase 220V Output – Terminals

Maximum output from the terminals (U, V, W) is 10kVA.

CURRENT ADJUSTMENT DIAL

BREAKER

CURRENT ADJUSTMENT

19

Image 20

Contents ＤＧＷ３１１ＤＭＤＧＷ３１１Ｌ Introduction Safety Guidelines Page DGW311DM DGW311L Specifications DGW311DM DGW311LUse PartsEquipment ECO Welding DGW311DM only Monitor Lamp Earth Leakage Breaker Earth Grounding Terminal Bonnet Grounding Grounding ROD Checking Engine Oil Slow-Down FeatureInitialization and Pre-check SAE10W/30 Checking Coolant/WaterLowest Ambient Temperature Mixture Ratio 30% 35% 45% Checking FuelOperation Initializing/Preparation Checking BatteryChecking Fuel, Engine Oil and Water Leakage Ishes ⑧ Keep the engine idle for about 5 minutesWelding Operation Selection Welding Cable „ Restart after stopping due to fuel shortageStopping Generator/Welder ECO Single Dual Welding Rod Φ2.0 φ4.0 Φ2.6 φ6.0 PolarityConnection Welding Cable Duty Cycle WeldingMaximum output from the terminals U, V, W is 10kVA 『DUAL 』35-280A45-310A φ2.0-φ6.0 380V 400V 415V 2.2 1-Phase Output Terminals 380V 400V 415VOutput Limitation Operation Simultaneous Use of Welding and Generating Checking and Maintenance Clean/Change Fuel Filter Adjust Tension V-BeltAdjust Engine Valve Clearance 50hrsRemove the cup and fuel filter element Turn the fuel line valve lever to 『CLOSE』Unscrew the retaining ring by turning counterclockwise, Long Term Storage Troubleshooting Insufficient FuelWater or contaminants in fuel Excessive Welding ArcNo AC output AC Output is WeakSlow-Down does not activate Engine does not stop Stop Solenoid disorderEngine Wiring Diagram DGW311L DGW311DMGenerator Wiring Diagram DGW311L W220B DGW311L W380A DGW311L W400A DGW311L W415A Telephone 81-82-849-2220 FAX