Shindaiwa 4 Cycle Diesel Engine specifications Output Limitation

Page 22

9-1.2.3 1-Phase Output – Terminals

1-Phase Output is available, using the 3-Phase output terminals and the other terminal (O). Maximum output available for the one set of terminals is 3kVA but the total output for 3 sets is 8kVA, which please note.

		DGW311L
	-(W)380A		-(W)400A	-(W)415A

Output
voltage	220V		230V	240V

<Caution>

zWhen using 1-Phase output, connect the loads evenly to each terminal set as much as pos- sible.

9-2 Output Limitation

Please refer to the following table, because electric tools and home appliances cannot be judged only by the rated output or the power consumption due to the efficiency and characteristic of the components.

DGW311DM-(W)220B, DGW311L-(W)220B :
Applicable Load (For reference purpose only)						(60Hz)

			Capacity (kW)

Loads	1-Phase 110V			1-Phase 220V			3-Phase
Loads							220V
							220V
	Receptacle	Terminal	Receptacle	Terminal	Terminal		Terminal
	1 unit	1 set	& Terminal	1 set	3 sets
			Total		Total

Electric Bulb, Heater, etc.	1.5	3.0	6.0	6.0	8.0		-

Electric Tools (Series Motor),	0.7	1.5	3.0	3.0	4.0		-
etc.

Mercury Bulb (High Power	0.6	1.2	2.4	2.4	3.2		-
Factor Type)

Submersible Pump, Com-	0.6	1.2	2.4	2.4	3.2		4.0
pressor, etc. (Induction Mo-
tor)

21

Image 22

Contents ＤＧＷ３１１ＤＭＤＧＷ３１１Ｌ Introduction Safety Guidelines Page DGW311DM DGW311L Specifications DGW311DM DGW311LUse PartsEquipment ECO Welding DGW311DM only Monitor Lamp Earth Leakage Breaker Earth Grounding Terminal Bonnet Grounding Grounding ROD Initialization and Pre-check Slow-Down FeatureChecking Engine Oil SAE10W/30 Checking Coolant/WaterLowest Ambient Temperature Mixture Ratio 30% 35% 45% Checking FuelChecking Fuel, Engine Oil and Water Leakage Checking BatteryOperation Initializing/Preparation Ishes ⑧ Keep the engine idle for about 5 minutesStopping Generator/Welder „ Restart after stopping due to fuel shortageWelding Operation Selection Welding Cable Connection Welding Cable PolarityECO Single Dual Welding Rod Φ2.0 φ4.0 Φ2.6 φ6.0 Duty Cycle Welding35-280A45-310A φ2.0-φ6.0 『DUAL 』Maximum output from the terminals U, V, W is 10kVA 380V 400V 415V 2.2 1-Phase Output Terminals 380V 400V 415VOutput Limitation Operation Simultaneous Use of Welding and Generating Checking and Maintenance Adjust Engine Valve Clearance Clean/Change Fuel FilterAdjust Tension V-Belt 50hrsUnscrew the retaining ring by turning counterclockwise, Turn the fuel line valve lever to 『CLOSE』Remove the cup and fuel filter element Long Term Storage Water or contaminants in fuel TroubleshootingInsufficient Fuel Excessive Welding ArcSlow-Down does not activate No AC outputAC Output is Weak Engine does not stop Stop Solenoid disorderEngine Wiring Diagram DGW311L DGW311DMGenerator Wiring Diagram DGW311L W220B DGW311L W380A DGW311L W400A DGW311L W415A Telephone 81-82-849-2220 FAX