Shindaiwa 4 Cycle Diesel Engine specifications Long Term Storage

Page 28

as well)

Reassemble it back. <Caution>

z Be sure to check for any contaminants on the packing, whenever reinstalling the cup.

z Turn the fuel line valve lever OPENafter assembling, and check for any leak. Confirming no leak, turn the fuel line valve CLOSE.

z Fuel Element Part No.: 124550-55700 (Yanmar)

11.5Draining Water from Fuel Tank

Drain Water

Every 200 hours

 

 

Unscrew the fuel drain plug.

Reinstall the drain plug, after draining the water entirdy.

11.6Changing Coolant/Water

Replace

Every 1 year or 1000 hours

 

 

SIDE DOOR

FUEL DRAIN

PLUG

WATER DRAIN PLUG

Remove the top plate.

Remove the radiator cap.

Loosen the water drain plug.

After draining all the water, reinstall the water drain plug. Remove the reservoir tank and replace all the water.

Install the reservoir tank back, and fill the radiator with coolant/water up to radiator filler neck. (Total cool- ant/water Capacity is 3.1 liter.)

Reinstall the radiator cap.

Install the top plate back.

TOP PLATE

RADIATOR CAP

WATER FILLER

SIDE DOOR

CAP

RESERVOIR TANK

12. Long - Term Storage

Danger : Electric Shock

zBefore performing any equipment check or maintenance, stop the engine, and remove the engine key. A person performing the maintenance should always keep the key.

Caution: Injuries

zBefore performing any equipment check or maintenance, stop the engine, and remove the engine key. A person performing the maintenance should always keep the key.

Caution : FireBurns

zWhen checking engine, always stop the engine, and keep away from fire.

zTemperature around muffler and exhaust can get extremely high. Wait until the engine cools down, before performing any checks.

27

Image 28
Contents DGW311DM DGW311L Introduction Safety Guidelines Page DGW311DM DGW311L Specifications DGW311DM DGW311LUse PartsEquipment ECO Welding DGW311DM only Monitor Lamp Earth Leakage Breaker Earth Grounding Terminal Bonnet Grounding Grounding ROD Initialization and Pre-check Slow-Down FeatureChecking Engine Oil SAE10W/30 Checking Coolant/WaterLowest Ambient Temperature Mixture Ratio 30% 35% 45% Checking FuelChecking Fuel, Engine Oil and Water Leakage Checking BatteryOperation Initializing/Preparation Ishes ⑧ Keep the engine idle for about 5 minutesStopping Generator/Welder „ Restart after stopping due to fuel shortageWelding Operation Selection Welding Cable Connection Welding Cable PolarityECO Single Dual Welding Rod Φ2.0 φ4.0 Φ2.6 φ6.0 Duty Cycle Welding35-280A45-310A φ2.0-φ6.0 『DUAL 』Maximum output from the terminals U, V, W is 10kVA 380V 400V 415V 2.2 1-Phase Output Terminals 380V 400V 415VOutput Limitation Operation Simultaneous Use of Welding and Generating Checking and Maintenance Clean/Change Fuel Filter Adjust Tension V-BeltAdjust Engine Valve Clearance 50hrsUnscrew the retaining ring by turning counterclockwise, Turn the fuel line valve lever to 『CLOSE』Remove the cup and fuel filter element Long Term Storage Troubleshooting Insufficient FuelWater or contaminants in fuel Excessive Welding ArcNo AC output AC Output is WeakSlow-Down does not activate Engine does not stop Stop Solenoid disorderEngine Wiring Diagram DGW311L DGW311DMGenerator Wiring Diagram DGW311L W220B DGW311L W380A DGW311L W400A DGW311L W415A Telephone 81-82-849-2220 FAX