Shindaiwa 4 Cycle Diesel Engine specifications Ishes, ⑧ Keep the engine idle for about 5 minutes

Page 16
FUEL LEVER

Danger : Suffocation from exhaust fume

zExhaust fume from the engine contains many elements harmful to human. Do not operate this equipment in poorly ventilated area, such as inside a room or in a tunnel.

Caution : Suffocation from exhaust fume

zDo not point the exhaust fume toward pedestrians or building.

Caution : Fire

zTemperature around muffler and exhaust can get extremely high. Keep any inflammable items (such as fuel, gas, paint, etc.) away from the equipment.

zAlways operate this equipment on flat surface and, at least 1 meter away from any objects (wall, box, etc.)

Caution : Injuries

zAlways place the equipment on flat and stable surface, to keep the equipment from sliding. Be sure to lock the wheels for the wheeled models.

zWhen starting the engine, turn off the connected equipment and set the circuit breaker to OFF position.

Turn the circuit breaker to OFF position.

Turn the fuel lever to OPEN.

Turn the Slow-Down switch to ON.

When the temperature is below 5,turn the starter switch to PREHEAT. The preheating lamp flashes 15

seconds. The lamp comes off when the PREHEAT fin-

CLOSE

ishes.

OPEN

Turn the starter switch to START to start the engine by the starter motor.

<Caution>

zDo not drive the starter motor for more than 15 seconds successively.

zIf you need to restart, wait for 30 seconds or more before retry.

Release the starter switch, as soon as the engine is started. <Caution>

z Once the engine is started, do not turn the starter switch to START. Make sure the frequency to the monitor on the control panel.

Keep the engine idle for about 5 minutes.

DGW311DM

DGW311L

 

STARTER SWITCH

 

CIRCUIT BREAKER

STARTER SWITCH

CIRCUIT BREAKER

 

 

 

 

 

SLOW-DOWN SWITCH

 

SLOW-DOWN SWITCH

PREHEAT LAMP

 

PREHEAT LAMP

 

 

 

 

 

 

 

 

 

 

 

 

 

15

Image 16
Contents DGW311DM DGW311L Introduction Safety Guidelines Page DGW311DM DGW311L Specifications DGW311DM DGW311LUse PartsEquipment ECO Welding DGW311DM only Monitor Lamp Earth Leakage Breaker Earth Grounding Terminal Bonnet Grounding Grounding ROD Initialization and Pre-check Slow-Down FeatureChecking Engine Oil SAE10W/30 Checking Coolant/WaterLowest Ambient Temperature Mixture Ratio 30% 35% 45% Checking FuelChecking Fuel, Engine Oil and Water Leakage Checking BatteryOperation Initializing/Preparation Ishes ⑧ Keep the engine idle for about 5 minutesStopping Generator/Welder „ Restart after stopping due to fuel shortageWelding Operation Selection Welding Cable Connection Welding Cable PolarityECO Single Dual Welding Rod Φ2.0 φ4.0 Φ2.6 φ6.0 Duty Cycle Welding35-280A45-310A φ2.0-φ6.0 『DUAL 』Maximum output from the terminals U, V, W is 10kVA 380V 400V 415V 2.2 1-Phase Output Terminals 380V 400V 415VOutput Limitation Operation Simultaneous Use of Welding and Generating Checking and Maintenance Clean/Change Fuel Filter Adjust Tension V-BeltAdjust Engine Valve Clearance 50hrsUnscrew the retaining ring by turning counterclockwise, Turn the fuel line valve lever to 『CLOSE』Remove the cup and fuel filter element Long Term Storage Troubleshooting Insufficient FuelWater or contaminants in fuel Excessive Welding ArcNo AC output AC Output is WeakSlow-Down does not activate Engine does not stop Stop Solenoid disorderEngine Wiring Diagram DGW311L DGW311DMGenerator Wiring Diagram DGW311L W220B DGW311L W380A DGW311L W400A DGW311L W415A Telephone 81-82-849-2220 FAX