DeWalt DWMT70786L instruction manual Preparation for USE, Proper Use Of The Tool, Work Stations

Page 12

English

PREPARATION FOR USE

Proper Use Of The Tool

Your new 3/8" Reversible Drill is designed for drilling, honing, reaming, hole sawing and wire bushing. The drill is also used to tighten and loosen threaded fasteners. The Jocobs® Keyless chuck provides fast and convenient change of drill bits. Do not use the tool for any other purpose than that specified without consulting the manufacturer or the manufacturer’s authorized supplier. To do so may be dangerous.

Never use the reversible drill as a hammer to dislodge or straighten cross threaded fasteners. Never attempt to modify the tool for other uses.

Work Stations

Your Reversible Drill should only be used as a hand operated tool. It is always recommended that the tool is used when standing with solid footing. It can be used in other positions but before any such use, the operator must be in a secure position having a firm grip and footing and be aware that when loosening fasteners the tool can move quite quickly away from the fastener being undone. An allowance must always be made for this rearward movement so as to avoid the possibility of hand/arm/body entrapment.

Putting Into Service

Air Supply

CAUTION: This air tool requires lubrication BEFORE initial use, also before and after each additional use.

WARNING: Use a clean lubricated air supply that will give a measured air pressure at the tool of 90 psi/6.2 bar when the tool is running with the trigger fully depressed.

Use recommended hose size. It is recommended that the tool is connected to the air supply as shown in figure A on page 11. Do not connect the tool to the air line system without

incorporating an easy to reach and operate air shut off valve. The air supply should be lubricated. It is strongly recommended that an air filter, regulator, lubricator (FRL) is used as shown in figure A on page 11 as this will supply clean, lubricated air at the correct pressure to the tool. Details of such equipment can be obtained from your supplier. If such equipment is not used then the tool should be lubricated by shutting off the air supply to the tool and then depressurizing the line by pressing the trigger on the tool. Disconnect the air line and pour into the air inlet 1 teaspoon (5cc.) of a suitable pneumatic motor lubricating oil, preferably incorporating a rust inhibitor. Reconnect tool to air supply and run tool slowly for a few seconds to allow air to circulate the oil.

Lubricate tool daily if used frequently, or when it starts to slow or lose power.

Using A Reversible Drill

WARNING:

1)Read all instructions before using this tool. All operators must be fully trained in its use and aware of these safety rules.

2)Do not exceed the maximum working air pressure of 90 psi/6.2 bar.

3)Use personal safety equipment.

4)Use only compressed air at the recommended conditions.

5)If the tool appears to malfunction, remove from use immediately and arrange for service and repair.

6)If the tool is used with a balancer or other support device, ensure that it is fixed securely.

7)Always keep hands away from the working attachment fitted to the tool.

8)The tool is not electrically insulated. Never use the tool if there is any chance of it coming into contact with live electricity.

9)When using the tool, always adopt a firm footing and/or position and grip the tool firmly to counteract any forces or

reaction forces that may be generated while using the tool.

12

Image 12
Contents DWMT70786L Reversible Drill Specifications DWMT70786L 3/8 Reversible DrillDefinitions Safety Guidelines Important Safety InstructionsEnglish What can Happen HOW to Prevent IT Using inflator nozzles for Keep handles dry, clean,Power tool For duster applicationsWhat can Happen CSA Z94.3 approved safety Which could resultGlasses with side shields Never leave operating toolSave These Instructions for Future USE Features Installation Safety Rules For Pneumatic ToolsAir Supply Fittings should have 1/4 NPT threadPutting Into Service Using a Reversible DrillPreparation for USE Proper Use Of The ToolPRE-START Checklist INSTALLING/REMOVING Drill BitsOperating Procedures SHUT-DOWN , PGOperating Instructions Maintenance Service InformationFull Three Years Warranty Glossary CFM Cubic feet per minuteID Inner diameter Perceuse Réversible 9,5 MM 3/8 PO Fiche TechniqueDirectives DE Sécurité Importantes Conserver CES InstructionsAVERTISSEMENT  Français Avertissement Risque D’EXPLOSION OU D’INCENDIE CE QUI Peut SE ProduireQUE Faire Comment Prévenir Avertissement Risque DE PERTED’OUÏE Avertissement Risque DE Blessure Suite Avertissement Risque D’ÉLECTROCUTIONEntretenir les outils de façon minutieuse Avertissement Arisque D’EMMÊLEMENT Conserver CES Directives Pour UN Usage Ultérieur Avertissement Arrivée D’AIR ET RaccordsCaractéristiques Alimentation d’air Pneumatiques Emploi Correct DE L’OUTIL Alimentation D’AIRUtilisation d’une perceuse réversible suite Liste DE Vérifications Avant DE Mettre L’OUTIL EN MarcheINSTALLER/RETIRER LES Mèches DE Perceuse Procédures DE Fonctionnement Mise EN Marche ,Arrêt , Instructions SUR LE FonctionnementEntretien GraissagePour graisser l’outil pneumatique à la main Information SUR LES RéparationsDeWALTpour en obtenir le remplacement gratuit GlossaireCompresor DE Aire DWMT70786L EspecificacionesInstrucciones DE Seguridad Importantes Guarde Estas InstruccionesAdvertencia Español Advertencia Riesgo DE Incendio O Explosión ¿QUÉ Puede SUCEDER?Advertencia Riesgo Respiratorio Asfixia ¿QUÉ Puede SUCEDER? Cómo EvitarloAdvertencia Riesgo DE Lesiones Advertencia Risque DE Blessure Suite Advertencia Riesgo DE Descarga EléctricaAdvertencia Riesgo DE Enredo Conserve Estas Instrucciones Para Futuras Consultas Advertencia Alimentación DE Aire Y ConexionesCaracterísticas Instalación Preparación Para EL USO Uso apropiado de la herramientaEstaciones de trabajo Puesta en servicioUso de un taladro reversible continuación Lista DE Comprobaciones PreviasINSTALACIÓN/EXTRACCIÓN DE LAS Brocas Procedimientos DE Operación Puesta EN Servicio , PÁG Parada , PÁGInstrucciones DE USO Mantenimiento RangementInformación DEL Servicio Técnico Garantía Completa DE UN TresGlosario Part No.DWMT70786L Copyright 2013 DeWALT