DeWalt DWMT70786L instruction manual Installation, Air Supply, Safety Rules For Pneumatic Tools

Page 11

Figure A

INSTALLATION

Air Supply

The recommended hook-up is shown in Figure A. Pneumatic tools operate on a wide range of air pressures. For maximum efficiency and longer tool life, the pressure of the air supplied to these tools MUST not exceed the rated PSI at the tool when the tool is running. Using a higher than rated pressure will cause faster wear and drastically shorten the tool’s life. A higher air pressure can also cause an unsafe condition and explosion.

The inside diameter of the hose should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D.

and fittings should have 1/4" NPT thread.

Safety Rules For Pneumatic Tools

1)Inspect the air hose for cracks or other problems. Replace the hose if worn.

2)Never point an air hose at another person.

3)Disconnect the tool when not in use, or before performing service or changing accessories.

4)Use proper hoses and fittings. Never use quick change couplings attached to the tool. Instead, add a hose and

coupling between the tool and the air supply.

English

The use of air line lubricators and air line filters is recommended to prevent water in the line that can damage the tool. Drain the air tank daily. Clean the air inlet filter screen on at least a weekly schedule to remove accumulated dirt or other matter that can restrict air flow.

The tool’s air inlet used for connecting an air supply has standard 1/4" NPT American thread.

	1/2”(or larger)
	Pipe and Fittings
	Coupler
	Tool
	Air Hose
	Oiler	Filter
	Leader Hose	Drain Daily
	Nipple	Drain Daily
	Nipple
	11

Image 11

Contents DWMT70786L Reversible Drill DWMT70786L 3/8 Reversible Drill SpecificationsImportant Safety Instructions Definitions Safety GuidelinesEnglish What can Happen HOW to Prevent IT For duster applications Using inflator nozzles forKeep handles dry, clean, Power toolWhat can Happen Never leave operating tool CSA Z94.3 approved safetyWhich could result Glasses with side shieldsSave These Instructions for Future USE Features Fittings should have 1/4 NPT thread InstallationSafety Rules For Pneumatic Tools Air SupplyProper Use Of The Tool Putting Into ServiceUsing a Reversible Drill Preparation for USEINSTALLING/REMOVING Drill Bits PRE-START ChecklistOperating Instructions Operating ProceduresSHUT-DOWN , PG Full Three Years Warranty MaintenanceService Information ID Inner diameter GlossaryCFM Cubic feet per minute Fiche Technique Perceuse Réversible 9,5 MM 3/8 POAVERTISSEMENT  Directives DE Sécurité ImportantesConserver CES Instructions Français QUE Faire Comment Prévenir Avertissement Risque D’EXPLOSION OU D’INCENDIECE QUI Peut SE Produire Avertissement Risque DE PERTED’OUÏE Entretenir les outils de façon minutieuse Avertissement Risque DE Blessure SuiteAvertissement Risque D’ÉLECTROCUTION Avertissement Arisque D’EMMÊLEMENT Avertissement Arrivée D’AIR ET Raccords Conserver CES Directives Pour UN Usage UltérieurCaractéristiques Alimentation d’air Pneumatiques Alimentation D’AIR Emploi Correct DE L’OUTILListe DE Vérifications Avant DE Mettre L’OUTIL EN Marche Utilisation d’une perceuse réversible suiteInstructions SUR LE Fonctionnement INSTALLER/RETIRER LES Mèches DE PerceuseProcédures DE Fonctionnement Mise EN Marche , Arrêt ,Information SUR LES Réparations EntretienGraissage Pour graisser l’outil pneumatique à la mainGlossaire DeWALTpour en obtenir le remplacement gratuitEspecificaciones Compresor DE Aire DWMT70786LAdvertencia Instrucciones DE Seguridad ImportantesGuarde Estas Instrucciones Español ¿QUÉ Puede SUCEDER? Cómo Evitarlo Advertencia Riesgo DE Incendio O Explosión¿QUÉ Puede SUCEDER? Advertencia Riesgo Respiratorio AsfixiaAdvertencia Riesgo DE Lesiones Advertencia Riesgo DE Descarga Eléctrica Advertencia Risque DE Blessure SuiteAdvertencia Riesgo DE Enredo Advertencia Alimentación DE Aire Y Conexiones Conserve Estas Instrucciones Para Futuras ConsultasCaracterísticas Instalación Puesta en servicio Preparación Para EL USOUso apropiado de la herramienta Estaciones de trabajoINSTALACIÓN/EXTRACCIÓN DE LAS Brocas Uso de un taladro reversible continuaciónLista DE Comprobaciones Previas Instrucciones DE USO Procedimientos DE Operación Puesta EN Servicio , PÁGParada , PÁG Garantía Completa DE UN Tres MantenimientoRangement Información DEL Servicio TécnicoGlosario Copyright 2013 DeWALT Part No.DWMT70786L