Ryobi YN301PL1 Transporting the AIR Compressor up or Down Stairs, Tool storage, Auto/off

Page 12

OPERATION

TRANSPORTING THE AIR COMPRESSOR up or DOWN STAIRS

See Figure 5, page 17.

To transport the air compressor down stairs:

nUsing the carrying handle get a firm grasp of the unit. Lift the unit into a safe and comfortable carrying position.

NOTE: Use good lifting techniques and get help if needed.

nWith proper footing and balance, carry the unit down one step at a time.

nUse care in transporting the unit down or up stairs to avoid damage to the stairs, damage to the unit, and personal injury.

nLower the air compressor until it sits securely on a flat surface.

tool storage

See Figure 6 - 7, page 17.

nPneumatic accessories may be stored in the accessory compartment.

NOTE: Always disconnect the tools from the air hose and securely close the accessory compartment before storage.

nCertain pneumatic nailers can be mounted to the sides of the air compressor using the side connect storage areas. Framing and roofing nailers should not be stowed in these storage areas as they are too large.

NOTE: Never rest the trigger of the nailer/stapler tool on this storage mount.

nThe air compressor should be stored on a stable flat surface either in the horizontal or upright position.

NOTE: Do not suspend the air compressor as it may result in damage to the air compressor or personal injury.

auto/off

See Figure 8, page 17.

nConnect the air compressor to a power supply. Turn the power switch to the AUTO position to power the compressor on, as shown in the start up section of the quick reference label.

NOTE: Do not run the compressor in the vertical position.

nTo turn the air compressor off, turn the power switch to the OFF position.

NOTE: When the compressor is in the AUTO position, the air compressor will automatically turn back on when the tank air pressure drops below the preset pressure limit. It will also shut off again when the max pressure is reached.

ReSETting the compressor

When amperage into the air compressor exceeds the specified amperage, the air compressor will automatically shut off.

To reset the air compressor:

nTurn the air compressor off.

nUnplug the air compressor to allow unit to cool and to trigger reset.

NOTE: If the overload protector is actuated, the motor must be allowed to cool down for 30 minutes.

nPlug the air compressor into an approved outlet.

nTurn the air compressor on.

WARNING

Never exceed the air tool’s pressure rating as recommended by the manufacturer. When using this air compressor as an inflation device, always follow the maximum inflation guidelines stated by the manufacturer of the item being inflated.

WARNING

Always ensure the switch is in the OFF position and the regulator pressure gauge reads zero (0) psi before changing air tools or disconnecting the hose from the air outlet. Failure to do so could result in possible serious personal injury.

CONNECTING/DISCONNECTING HOSES TO THE AIR COMPRESSOR

See Figures 8 - 10, pages 17 - 18.

When connecting a pneumatic air nailer or other air tool always follow the manufacturer’s recommended start-up procedure.

When connecting/disconnecting a hose to the air compressor always do the following:

nEnsure AUTO/OFF switch is in the OFF position and the air compressor is unplugged.

nConfirm that the outlet pressure is at zero (0) psi by fully turning the regulator knob counterclockwise to fully re- duce air pressure at the outlet.

NOTE: Turning the knob clockwise increases air pressure at the outlet. Turning counterclockwise reduces air pres- sure at the outlet.

nAttach coiled air hose to coupler on the side of the air compressor.

nConnect the air compressor to a power supply and turn power switch to the AUTO position.

12 - English

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionGeneral Safety Rules Electrical SafetyPersonal safety Work AreaSpecific Safety Rules ServiceSpecific Safety Rules Symbols Symbol NameSymbol Signal Meaning Disclaimer of Warranties Electrical Extension CordsElectrical Connection Grounding InstructionsFeatures Product SpecificationsGlossary of Terms Cord WrapAssembly Operation ApplicationsTransporting the AIR Compressor See 4,ReSETting the compressor CONNECTING/DISCONNECTING Hoses to the AIR CompressorTransporting the AIR Compressor up or Down Stairs Tool storageChecking the Safety Valve Draining the TankTo disconnect a coiled air hose See 13,Maintenance General MaintenanceLubrication Troubleshooting Problem Cause SolutionGarantie Table DES MatièresRègles de sécurité générales Conserver CES Instructions Lieu DE TravailSécurité Électrique Sécurité PersonnelleRègles de sécurité particulières DépannageRègles de sécurité particulières Symboles Symbole NOM Désignation / ExplicationSymbole Signal Signification AVERTISSEMENT Exonération DE Garanties Caractéristiques électriques Cordons prolongateursConnexion électrique Longueur Calibre de fil Du cordonGlossaire CaractéristiquesP R E N D R E À C O N N a Î T R E L­ E Compresseur Rembobineur DE CordonAssemblage Utilisation Transport DU Compresseur D’AIRApplications Voir les figures 3 4,Transport DU Compresseur D’AIR PAR UN Escalier Outils de rangementFonctionnement AUTOMATIQUE/ARRÊT AUTO/OFF Réinitialiser le CompresseurUtilisation DU Compresseur D’AIR Purge DES RéservoirVérification DE LA Soupape DE Sûreté Voir la figures 12 13,Entretien Entretien GénéralLubrification Problème Cause Solution DépannageÍndice DE Contenido IntroducciónGarantía Reglas DE Seguridad Generales Guarde Estas Instrucciones Área DE TrabajoSeguridad Eléctrica Empleo Y Cuidado DE LA HerramientaReglas DE Seguridad Específicas ServicioReglas DE Seguridad Específicas Símbolos PeligroSímbolo Nombre DENOMINACIÓN/EXPLICACIÓN Símbolo Señal SignificadoPeligro Extención DE Responsabilidad DE LAS GarantíasAspectos eléctricos AdvertenciaLongitud Calibre conductores Del cordón Vea la figura 1, paginaGlosario de términos CaracterísticasCaracterísticas ArmadoFuncionamiento UsosTraslado DEL Compresor DE Aire PrecauciónCómo Bajar EL Compresor DE Aire POR LAS Escaleras Almacenamiento DE LA HerramientaAUTOMÁTICO/APAGADO Reajuste DEL CompresorConexión DE UNA Herramienta Neumática AL Compresor DE Aire Utilización DEL Compresor DE AireDrenado DEL Tanque Vea la figura 11, paginaMantenimiento Revisión de la válvula de seguridadLubricación Vea la figura 12, paginaSolución de problemas Problema Causa SoluciónPatilla de conexión a tierra Page Page Page YN301PL / YN301PL1 Manuel D’UTILISATION / Manual DEL OperadorONE World TECHNOLOGIES, INC

YN301PL1, YN301PL specifications

The Ryobi YN301PL and YN301PL1 represent a significant innovation in the field of power tools, specifically aiming to enhance the user's experience with efficient and effective performance. These models are designed with a user-friendly approach, catering to DIY enthusiasts and professionals alike.

One of the prominent features of the Ryobi YN301PL and YN301PL1 is their powerful motor, which delivers robust performance for various applications. The efficient motor significantly reduces vibration, enabling smoother and more precise control during operation. This feature is particularly advantageous for tasks requiring extended use, minimizing user fatigue.

Both models boast a lightweight and ergonomic design, making them easy to handle and maneuver. The balanced weight distribution ensures that users can work for longer periods without straining their wrists or arms. This thoughtful design is complemented by a comfortable grip, which enhances user control and stability.

In terms of versatility, the Ryobi YN301PL and YN301PL1 support multiple attachments and accessories, allowing users to tackle a range of projects, from sanding and polishing to drilling and cutting. This adaptability makes them suitable for various materials, including wood, metal, and plastic, ensuring that users can seamlessly switch between tasks without needing multiple tools.

The inclusion of advanced technology further enhances the performance of both models. The integrated speed control feature allows users to adjust the operational speed for different tasks, providing greater precision and versatility. This is particularly useful in delicate applications where a gentle touch is required.

Durability is another hallmark of the Ryobi YN301PL and YN301PL1. Constructed with high-quality materials, these tools are built to withstand rigorous use. The robust design not only enhances longevity but also ensures reliability even under demanding conditions.

Lastly, both models prioritize safety, incorporating protective features that safeguard users during operation. These measures not only enhance the overall user experience but also instill confidence in those using the tools for both light and heavy-duty tasks.

In conclusion, the Ryobi YN301PL and YN301PL1 stand out due to their powerful performance, ergonomic design, versatility, advanced technology, and safety features. They are ideal tools for anyone looking to elevate their DIY projects or professional jobs, ensuring that quality and efficiency are always within reach.
Top Page Image Contents