Ryobi P500 manual Attaching the Blade, Removing the Blade

Page 10

ASSEMBLY

ATTACHING THE BLADE

See Figure 2.

WARNING:

A 5-1/2 in. blade is the maximum blade capacity of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guard, while thicker blades will prevent blade screw from se- curing blade on spindle. Either of these situations could result in a serious accident.

Remove the battery pack from the saw.

n Remove the blade wrench (5 mm hex key) from the stor-

age area.

n Depress the spindle lock button and remove the blade

SPINDLE

LOCK BUTTON

0

5 5

4 0

5

30 22

3

2

1

45

 

0

 

1

LOWER BLADE

GUARD HANDLE

SPINDLE

BLADE

screw and outer blade washer.

NOTE: Turn the blade screw clockwise to remove.

CAUTION:

To prevent damage to the spindle or spindle lock, always allow motor to come to a complete stop before engaging spindle lock.

NOTE: Do not run the circular saw with spindle lock en- gaged.

nWipe a drop of oil onto the inner blade washer and outer blade washer where they contact the blade.

WARNING:

If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly.

nFit the saw blade inside the lower blade guard and onto the spindle.

NOTE: The saw teeth point upward at the front of the saw.

nReplace the outer blade washer.

nDepress the spindle lock button, then replace the blade screw. Tighten the blade screw securely by turning it clockwise.

nReturn the blade wrench to the storage area.

NOTE: Never use a blade that is too thick to allow the outer blade washer to engage with the flats on the spindle.

REMOVING THE BLADE

See Figure 3.

Remove the battery pack from the saw.

nRemove the blade wrench from the storage area.

INNER

BLADE WASHER

OUTER

BLADE WASHER

BLADE SCREW

Fig. 2

 

LOWER BLADE

SPINDLE LOCK

GUARD LEVER

 

 

 

SPINDLE

0

 

 

LOCK

3

 

 

SCREW

5

 

 

 

5

 

 

 

40

 

 

 

5

 

 

 

0

 

 

 

2

 

 

 

2

 

 

 

 

TO LOOSEN

 

 

3

 

 

 

2

 

 

 

1

5

 

 

 

4

 

 

 

0

 

 

 

1

TO TIGHTEN

 

 

 

Fig. 3

 

 

 

nPosition the saw as shown, depress the spindle lock button, and remove the blade screw by turning it clock- wise.

nRemove the outer blade washer.

nRemove the blade.

10

Image 10
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionPersonal Safety General Safety RulesElectrical Safety Work AreaService Specific Safety RulesCauses and Operator Prevention of Kickback Additional Safety Rules Laser Guide WarningsSymbols Name DESIGNATION/EXPLANATIONSymbol Signal Meaning Features Product SpecificationsAssembly Attaching the Blade Removing the BladeDepress Latches to Remove Battery Pack Install Installing the Battery PackRemoving the Battery Pack OperationSee Figures 5 KickbackWrong Kickback Blade SET TOO Deep Incorrect SupportBlade Guard System LOCK-OFF Button SwitchSAW Blades STARTING/STOPPING the SAWTo Raise SAW Base Assembly Adjusting Blade DepthUsing the Laser Guide Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFSee Figures 13 Operating the SAWWrong TOP View of SAW Guideline Blade Guide Notch Cross CUTTING/RIP CuttingRIP Cutting Edge ClampMaking a Bevel CUT Adjusting the Bevel SettingBevel Cutting See Figures 19Pocket Cutting Pocket CUT Lower Blade GuardAdjusting the Laser AdjustmentsAdjusting Positive 0 Bevel Stop Positive 0 Bevel StopGeneral Maintenance MaintenanceReplacing Laser Guide Batteries Battery Pack Removal and Preparation for Recycling AccessoriesBatteries Parts and Service Manuel D’UTILISATION Conserver CE Manuel Pour Future RéférenceGarantie Table DES MatièresRègles DE Sécurité Générales Avertissement ! Dépannage Règles DE Sécurité ParticulièresCauses DU Rebond ET Précautions À Prendre Règeles Supplémentaires Pour LA Sécurité DU Fonctionnement Mises en garde concernant le guide laserSymboles Symbole NOM Désignation / ExplicationAVERTISSEMENT  Symbole Signal SignificationAvertissement Caractéristiques Fiche TechniqueAssemblage Installation DE LA Lame Retrait DE LA LameRetrait DU Bloc DE BATTERIES  Installation DU Bloc DE BATTERIES Utilisation ApplicationsIncorrect RebondVoir les figures 5 à Système DE Garde DE Lame Lames DE ScieMise EN Marche ET Arrêt DE LA Scie Pour Relever LA Lame Base Réglage DE LA Profondeur DE CoupeUtilisation DU Guide Laser PourUtilisation DE LA Scie Voir les figures 13 àCoupe Transversale ET Refente RefenteVoir les figures 19 à Coupe EN BiseauRéglage D’ANGLE DE Biseau Bouton DE Réglage DE BiseauÉvidements Évidement Garde DE LameVérification DE LA Butée Fixe DE Biseau À RéglagesButée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀEntretien Remplacement DES Piles DU Guide LaserEntretien Général Accessoires Retrait ET Préparation DU Batteries Pour LE RecyclagePièces ET Service Manual DEL Operador Guarde Este Manual Para Futuras ConsultasIntroducción Índice DE ContenidoGarantía Seguridad Eléctrica Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad PersonalServicio Reglas DE Seguridad EspecíficasCausas Y Prevención DE Contragolpes Reglas Importantes Para LAS Productos DE Baterías Advertencias relacionadas con la guía láserSímbolos Símbolo Nombre DENOMINACIÓN/EXPLICACIÓNServicio Advertencia PeligroPrecaución Símbolo Señal SignificadoCaracterísticas Especificaciones DEL ProductoArmado Desmontaje DE LA Hoja DE Corte Montaje DE LA HojaPara Aflojar Para Apretar Instalación DEL Paquete DE Baterías FuncionamientoAplicaciones Desmontaje DEL Paquete DE BateríasContragolpe Forma IncorrectaEncendido Y Apagado DE LA Sierra Hojas DE LA SierraSistema DE Protección DE LA Hoja InterruptorPara Subir LA Sierra Conjunto DE LA Base Ajuste DE LA Profundidad DE LA HojaUtilización DE LA Guía Láser Interruptor DE LA Guía Láser ENC./ ApagVea las figuras 13 a Utilización DE LA SierraForma Incorrecta Cortes Transversales Y AL Hilo Cortes AL HiloForma DE Efectuar Cortes a Bisel Corte a BiselAjuste DEL Ángulo DE Bisel Vea las figuras 19 aCorte EN Cavidad Revisión DEL Tope DE Bisel a AjustesTope DE Bisel a Ajuste DEL Tope DE Bisel aMantenimiento General MantenimientoReemplazo DE LAS Baterías DE LA Guía Láser Accesorios BateríasNotas Notas Piezas DE Repuesto Y Servicio ONE World TECHNOLOGIES, INC
Related manuals
Manual 24 pages 641 b Manual 68 pages 61.41 Kb