Ryobi P500 manual Accessories, Batteries, Battery Pack Removal and Preparation for Recycling

Page 21

MAINTENANCE

BATTERIES

This product will accept Ryobi One+18V lithium-ion batteriy packs or Ryobi One+ 18 V nickel-cadmium batteriy packs. Length of service from each charging will depend on the type of work you are doing.

The batteries for this product have been designed to provide maximum trouble-free life. However, like all batteries, they will eventually wear out. Do not disassemble battery pack and attempt to replace the batteries. Handling of these batteries, especially when wearing rings and jewelry, could result in a serious burn.

To obtain the longest possible battery life, we suggest the following:

For lithium-ion batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F and away from moisture.

Store battery packs in a 30%-50% charged condition.

Every six months of storage, charge the pack as normal.

For nickel-cadmium batteries:

Remove the battery pack from the charger once it is fully charged and ready for use.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 80°F.

Store battery packs in a “discharged” condition.

BATTERY PACK REMOVAL AND PREPARATION FOR RECYCLING

To preserve natural resources, please recycle or dispose of batteries properly.

Li - Ion

This product uses nickel-­cadmium and

 

lithium-ion batteries. Local, state or

 

federal laws may prohibit disposal of

 

batteries in ordinary trash.

Consult your local waste authority for information regarding­ available recycling and/or disposal options.

WARNING:

Upon removal, cover the battery pack’s terminals with heavy-duty adhesive tape. Do not attempt to destroy or disassemble battery pack or remove any of its compo- nents. Lithium-ion and nickel-cadmium batteries must be recycled or disposed of properly. Also, never touch both terminals with metal objects and/or body parts as short circuit may result. Keep away from children. Failure to comply with these warnings could result in fire and/or serious injury.

ACCESSORIES

The following recommended accessories are currently available at retail stores:

n5-1/2 in. Thin Kerf Blade

WARNING:

Current attachments and accessories available for use with this tool are listed above. Do not use any attachments or ac- cessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

21

Image 21
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyElectrical Safety General Safety RulesPersonal Safety Work AreaSpecific Safety Rules ServiceCauses and Operator Prevention of Kickback Laser Guide Warnings Additional Safety RulesName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Product Specifications FeaturesAssembly Removing the Blade Attaching the BladeRemoving the Battery Pack Installing the Battery PackDepress Latches to Remove Battery Pack Install OperationWrong KickbackSee Figures 5 Kickback Blade SET TOO Deep Incorrect SupportSAW Blades LOCK-OFF Button SwitchBlade Guard System STARTING/STOPPING the SAWUsing the Laser Guide Adjusting Blade DepthTo Raise SAW Base Assembly Depth To Adjustment Loosen Knob Laser Guide Switch ON/OFFOperating the SAW See Figures 13Wrong RIP Cutting Cross CUTTING/RIP CuttingTOP View of SAW Guideline Blade Guide Notch Edge ClampBevel Cutting Adjusting the Bevel SettingMaking a Bevel CUT See Figures 19Pocket CUT Lower Blade Guard Pocket CuttingAdjusting Positive 0 Bevel Stop AdjustmentsAdjusting the Laser Positive 0 Bevel StopMaintenance General MaintenanceReplacing Laser Guide Batteries Accessories Battery Pack Removal and Preparation for RecyclingBatteries Parts and Service Conserver CE Manuel Pour Future Référence Manuel D’UTILISATIONTable DES Matières GarantieAvertissement !  Règles DE Sécurité GénéralesRègles DE Sécurité Particulières DépannageCauses DU Rebond ET Précautions À Prendre Mises en garde concernant le guide laser Règeles Supplémentaires Pour LA Sécurité DU FonctionnementSymbole NOM Désignation / Explication SymbolesSymbole Signal Signification AVERTISSEMENT Avertissement Fiche Technique CaractéristiquesAssemblage Retrait DE LA Lame Installation DE LA LameUtilisation Installation DU Bloc DE BATTERIES Retrait DU Bloc DE BATTERIES  ApplicationsRebond IncorrectVoir les figures 5 à Lames DE Scie Système DE Garde DE LameMise EN Marche ET Arrêt DE LA Scie Utilisation DU Guide Laser Réglage DE LA Profondeur DE CoupePour Relever LA Lame Base PourVoir les figures 13 à Utilisation DE LA ScieRefente Coupe Transversale ET RefenteRéglage D’ANGLE DE Biseau Coupe EN BiseauVoir les figures 19 à Bouton DE Réglage DE BiseauÉvidement Garde DE Lame ÉvidementsButée Fixe DE Biseau À RéglagesVérification DE LA Butée Fixe DE Biseau À Réglage DE LA Butée Fixe DE Biseau ÀRemplacement DES Piles DU Guide Laser EntretienEntretien Général Retrait ET Préparation DU Batteries Pour LE Recyclage AccessoiresPièces ET Service Guarde Este Manual Para Futuras Consultas Manual DEL OperadorÍndice DE Contenido IntroducciónGarantía ¡ADVERTENCIA Reglas DE Seguridad GeneralesSeguridad Eléctrica Seguridad PersonalReglas DE Seguridad Específicas ServicioCausas Y Prevención DE Contragolpes Advertencias relacionadas con la guía láser Reglas Importantes Para LAS Productos DE BateríasSímbolo Nombre DENOMINACIÓN/EXPLICACIÓN SímbolosPrecaución PeligroServicio Advertencia Símbolo Señal SignificadoEspecificaciones DEL Producto CaracterísticasArmado Montaje DE LA Hoja Desmontaje DE LA Hoja DE CortePara Aflojar Para Apretar Aplicaciones FuncionamientoInstalación DEL Paquete DE Baterías Desmontaje DEL Paquete DE BateríasForma Incorrecta ContragolpeSistema DE Protección DE LA Hoja Hojas DE LA SierraEncendido Y Apagado DE LA Sierra InterruptorUtilización DE LA Guía Láser Ajuste DE LA Profundidad DE LA HojaPara Subir LA Sierra Conjunto DE LA Base Interruptor DE LA Guía Láser ENC./ ApagUtilización DE LA Sierra Vea las figuras 13 aForma Incorrecta Cortes AL Hilo Cortes Transversales Y AL HiloAjuste DEL Ángulo DE Bisel Corte a BiselForma DE Efectuar Cortes a Bisel Vea las figuras 19 aCorte EN Cavidad Tope DE Bisel a AjustesRevisión DEL Tope DE Bisel a Ajuste DEL Tope DE Bisel aMantenimiento Mantenimiento GeneralReemplazo DE LAS Baterías DE LA Guía Láser Baterías AccesoriosNotas Notas ONE World TECHNOLOGIES, INC Piezas DE Repuesto Y Servicio
Related manuals
Manual 24 pages 641 b Manual 68 pages 61.41 Kb