Ryobi P500 manual Service, Symbol Signal Meaning

Page 7

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL

SIGNAL

MEANING

 

 

 

 

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

 

in death or serious injury.

 

 

 

 

 

 

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

 

in death or serious injury.

 

 

 

 

 

 

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

 

minor or moderate injury.

 

 

 

 

 

 

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

 

damage.

 

 

SERVICE

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to the nearest AUTHORIZED SERVICE CENTER for repair. When servic- ing, use only identical replacement parts.

WARNING:

To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator’s manual. If you do not understand the warnings and instructions in the operator’s manual, do not use this product. Call Ryobi customer service for assistance.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

SAVE THESE INSTRUCTIONS

7

Image 7
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyWork Area General Safety RulesElectrical Safety Personal SafetyService Specific Safety RulesCauses and Operator Prevention of Kickback Laser Guide Warnings Additional Safety RulesName DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning Product Specifications FeaturesAssembly Removing the Blade Attaching the BladeOperation Installing the Battery PackRemoving the Battery Pack Depress Latches to Remove Battery Pack InstallKickback Blade SET TOO Deep Incorrect Support KickbackWrong See Figures 5STARTING/STOPPING the SAW LOCK-OFF Button SwitchSAW Blades Blade Guard SystemDepth To Adjustment Loosen Knob Laser Guide Switch ON/OFF Adjusting Blade DepthUsing the Laser Guide To Raise SAW Base AssemblySee Figures 13 Operating the SAWWrong Edge Clamp Cross CUTTING/RIP CuttingRIP Cutting TOP View of SAW Guideline Blade Guide NotchSee Figures 19 Adjusting the Bevel SettingBevel Cutting Making a Bevel CUTPocket CUT Lower Blade Guard Pocket CuttingPositive 0 Bevel Stop AdjustmentsAdjusting Positive 0 Bevel Stop Adjusting the LaserGeneral Maintenance MaintenanceReplacing Laser Guide Batteries Battery Pack Removal and Preparation for Recycling AccessoriesBatteries Parts and Service Conserver CE Manuel Pour Future Référence Manuel D’UTILISATIONTable DES Matières GarantieAvertissement !  Règles DE Sécurité GénéralesDépannage Règles DE Sécurité ParticulièresCauses DU Rebond ET Précautions À Prendre Mises en garde concernant le guide laser Règeles Supplémentaires Pour LA Sécurité DU FonctionnementSymbole NOM Désignation / Explication SymbolesAVERTISSEMENT  Symbole Signal SignificationAvertissement Fiche Technique CaractéristiquesAssemblage Retrait DE LA Lame Installation DE LA LameApplications Installation DU Bloc DE BATTERIES Utilisation Retrait DU Bloc DE BATTERIES Incorrect RebondVoir les figures 5 à Système DE Garde DE Lame Lames DE ScieMise EN Marche ET Arrêt DE LA Scie Pour Réglage DE LA Profondeur DE CoupeUtilisation DU Guide Laser Pour Relever LA Lame BaseVoir les figures 13 à Utilisation DE LA ScieRefente Coupe Transversale ET RefenteBouton DE Réglage DE Biseau Coupe EN BiseauRéglage D’ANGLE DE Biseau Voir les figures 19 àÉvidement Garde DE Lame ÉvidementsRéglage DE LA Butée Fixe DE Biseau À RéglagesButée Fixe DE Biseau À Vérification DE LA Butée Fixe DE Biseau ÀEntretien Remplacement DES Piles DU Guide LaserEntretien Général Retrait ET Préparation DU Batteries Pour LE Recyclage AccessoiresPièces ET Service Guarde Este Manual Para Futuras Consultas Manual DEL OperadorIntroducción Índice DE ContenidoGarantía Seguridad Personal Reglas DE Seguridad Generales¡ADVERTENCIA Seguridad EléctricaServicio Reglas DE Seguridad EspecíficasCausas Y Prevención DE Contragolpes Advertencias relacionadas con la guía láser Reglas Importantes Para LAS Productos DE BateríasSímbolo Nombre DENOMINACIÓN/EXPLICACIÓN SímbolosSímbolo Señal Significado PeligroPrecaución Servicio AdvertenciaEspecificaciones DEL Producto CaracterísticasArmado Desmontaje DE LA Hoja DE Corte Montaje DE LA HojaPara Aflojar Para Apretar Desmontaje DEL Paquete DE Baterías FuncionamientoAplicaciones Instalación DEL Paquete DE BateríasForma Incorrecta ContragolpeInterruptor Hojas DE LA SierraSistema DE Protección DE LA Hoja Encendido Y Apagado DE LA SierraInterruptor DE LA Guía Láser ENC./ Apag Ajuste DE LA Profundidad DE LA HojaUtilización DE LA Guía Láser Para Subir LA Sierra Conjunto DE LA BaseVea las figuras 13 a Utilización DE LA SierraForma Incorrecta Cortes AL Hilo Cortes Transversales Y AL HiloVea las figuras 19 a Corte a BiselAjuste DEL Ángulo DE Bisel Forma DE Efectuar Cortes a BiselCorte EN Cavidad Ajuste DEL Tope DE Bisel a AjustesTope DE Bisel a Revisión DEL Tope DE Bisel aMantenimiento General MantenimientoReemplazo DE LAS Baterías DE LA Guía Láser Baterías AccesoriosNotas Notas ONE World TECHNOLOGIES, INC Piezas DE Repuesto Y Servicio
Related manuals
Manual 24 pages 641 b Manual 68 pages 61.41 Kb