Bostitch BT1855K manual Trigger Lockout Control, Trip Operation Mode, Contacttrip, Sequential Trip

Page 8

TRIGGER LOCKOUT CONTROL

The trigger lockout control feature on BOSTITCH pneumatic tools provides a trigger lock feature for added safety control. Push the lockout control button in or out to activate or lock the tool trigger.

Trigger Lockout Control Button

TRIP OPERATION MODE

Warning: Always disconnect air supply before making adjustments as accidental actuation may occur, possibly causing injury.

The BT1855 and SX1838 feature a selectable trigger system that allows the user to choose between the following modes of operation:

1. Contact TripOperation

2. Sequential Trip Operation

1.CONTACTTRIP:

The common operation procedure on “Contact Trip” tools is for the operator to contact the work surface to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work surface is contacted. This will allow rapid fastener placement on many jobs. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if unintentionally allowed to re- contact the work surface with the trigger still actuated (finger still holding the trigger pulled) an unwanted second fastener will be driven.

2.SEQUENTIAL TRIP:

The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This makes accurate fastener placement easier. The Sequential Trip allows exact fastener location without the possibility if driving a second fastener on recoil as described under “Contact Trip”. The Sequential Trip Tool has a positive advantage because it will not accidentally drive a fastener if the tool is contacted against the work surface - or anything else - while the operator is holding the trigger pulled.

SELECTING THE TRIP MODE:

To ensure safety, the user must lock the trigger (as described above) before changing the trigger system. To change the trip mode, rotate the mode switch in the counterclockwise direction. The mode switch will lock automatically when the indicating arrow is pointing down to the 3 nail icon stamped into the tool frame (Contact Trip Mode) or to a single nail icon stamped in the tool frame( Sequential Trip Mode). Unlock the trigger to resume tool operation.

Contact Trip Mode

Sequential Trip Mode

(trip mode selector switch pointing down)

(trip mode selector switch pointing up)

-8-

Image 8
Contents BT1855 & SX1838 Introduction IndexSafety Instructions AIR Supply and ConnectionsLoadingtool OperationTool Components Tool Specifications Fastener SpecificationsAIR Supplyand Connections Loadingthe BT1855 & SX1838 Loading the SX1838Trip Operation Mode Selecting the Trip ModeTrigger Lockout Control ContacttripDIAL-A-DEPTH Fastener Control Adjustment BOSTITCH, INCHEX Wrench Storage Installing the Belt HookUsingthe Integrated Pencil Sharpener Tool Operation Before Handling or Operating this ToolContact Trip Operation Sequential Trip OperationJAM Clearing Procedure BT1855 JAM Clearing SX1838 JAM ClearingReplacement Parts Assembly Procedure for SealsAIR SUPPLY-PRESSURE and Volume Tool Operation CheckMaintenance Checklist Maintenance Benefit Procedure Service IntervalCausecorrection TroubleshootingProblem Availableaccessories Bostitch Finish &TRIM Products Nota IntroducciónÍndice Instrucciones DE Seguridad Suministro DE Airey ConexionesCarga DE LA Herramienta FuncionamientoComponentes DE LA Herramienta Nota Especificaciones DE LA HerramientaEspecificaciones DE Fijaciones Conectores ManguerasFuente DE Suministro ReguladorCarga DE LA BT1885Y LA SC1838 Carga DE LA SX1838Control DE Bloqueo DEL Gatillo Modo DE Funcionamiento DEL DisparadorDisparo DE Contacto Disparo SecuencialAjuste DE Control DE Fijaciones DIAL-A-DEPTH Almacenamiento DE LA Llave Hexagonal Instalación DEL Gancho Para EL CinturónUSO DEL Sacapuntas Integrado Funcionamiento DE LA Herramienta Antes DE Manipular U Operar Esta HerramientaFuncionamiento DEL Disparo DE Contacto Funcionamiento DEL Disparo SecuencialProcedimiento Para Despejar Atascos Presión Y Volumen DEL Suministro DE Aire Revisión Funcional DE LA HerramientaMantenimiento DE LA Herramienta Neumática Piezas DE RepuestoLista DE Verificación DE Mantenimiento Mantenimiento Beneficio Procedimiento Intervalo De servicioSolución DE Problemas Problema Causa CorrecciónAccesorios Disponibles Productos Bostitch Para Rematey Detalle Remarque Garantie Limitée É.-U. et Canada seulementConsignes DE Sécurité Alimentation Dair ET ConnexionsChargement DE L’OUTIL FonctionnementComposants DE Loutil Remarque Spécifications DE L’OUTILCaractéristiques DES Attaches Raccords TuyauxsouplesSource D’ALIMENTATION RégulateurChargement DE LA BT1855 ET DE LA SX1838 Chargement DE LA SX1838Commande DE Blocage DE Gâchette Mode DE DéclenchementSÉLECTION/CHANGEMENT DU Mode DE Déclenchement Déclenchement SUR ContactAjustement DE LA Commande D’ATTACHE DIAL-A-DEPTH Rangement DE LA CLÉ HEX Installation DU Crochet DE CeinturePour Utiliser LETAILLE-CRAYON Intégré Fonctionnement DE L’OUTIL Fonctionnement EN Mode Déclenchement SUR ContactFonctionnement EN Mode Déclenchement Séquentiel Procédure Pour LE Dégagement DES Blocages Alimentation DAIR-PRESSION ET Volume Vérification DU Fonctionnement DE L’OUTILEntretien DE L’OUTIL Pneumatique Pièces DE RechangeEntretien Bienfait Procédure Intervalle De service Liste DE Vérification Pour L’ENTRETIENProblème CausesolutionDépannage Accessoires Disponibles Produits DE Finition ET D’HABILLAGE Bostitch