Delta TP305 Leveling Extension Tables, Knife Transfer Tool Storage, Wrench Storage

Page 11

LEVELING EXTENSION TABLES

The extension tables (A) and (G) Fig. 14 must be level with the planer table. To check the extension tables and adjust if necessary:

1.Place a straight edge (B) Fig. 14 on the planer table

(E)with one end extending out over the infeed table

(A).Check to see if the infeed table is level with the planer table on both ends of the planer table.

2.If an adjustment is necessary, loosen the locknut (C) Fig. 14, and adjust the stop screw (D) on each side of the infeed table (A) until the extension table is level with the planer table (E). Tighten the locknut

(C).Recheck and make certain that the inside edge of table extension is level with the planer table. If necessary, loosen the two screws (F), adjust the extension table and retighten the two screws

(F).Adjust the opposite side of the table in the same manner. Make certain that the extension table is solidly supported when downward pressure on the table is applied.

3.Check and adjust the outfeed table (G) in the same manner.

Fig. 14

 

 

 

G

E

A

C

D

 

 

 

F

 

 

 

 

 

B

KNIFE TRANSFER TOOL STORAGE

The knife transfer tool (A) Fig. 15, supplied with your planer, can easily be stored underneath the outfeed table extension (B) when not being used. A Velcro strip (C) is provided on the tool and underneath the table for this purpose.

Fig. 15

C

A

B C

WRENCH STORAGE

The wrench (A) Fig. 16, can be stored in hole (B) located on the right rear side of the machine as shown.

11

Fig. 16

A

B

Image 11
Contents Contractors Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing General Safety RulesRefer to them often and use them to instruct others Additional Specific Safety RulesGrounding Instructions Power ConnectionsMotor Specifications Functional Description Carton ContentsRaising and Lowering Handle AssemblyAssembly Tools Required Assembly Time EstimateStarting and Stopping Planer OperationCutterhead Guard Fastening Planer to Supporting SurfaceRaising and Lowering Head Assembly Locking Switch in the OFF PositionWrench Storage Leveling Extension TablesKnife Transfer Tool Storage Carrying HANDLE/STOCK Transfer BAR Replacing KnivesThese knobs were removed in Step Lubrication & Rust Protection Troubleshooting MaintenanceKeep Machine Clean Failure to StartLubrication Brush Inspection ReplacementReplacement Parts ServiceAccessories WarrantyFrançaise LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Conservez CES InstructionsLutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles Spécifiques Additionnelles DE SûretéInstructions DE Mise À LA Terre Raccordements ÉlectriquesSpécifications DU Moteur Cordon DE Rallonge Description FonctionnelleContenus DE Boite AVANT-PROPOSAbaisser LES Rallonges DE Table AssemblageDésemballage ET Nettoyage Outils Nécessaires Pour L’ASSEMBLAGEDémarrage ET Arrêt DE LA Raboteuse FonctionnementDispositif DE Protection DES Fers Fixation DE LA Raboteuse SUR UNE Surface DE SupportSoulèvement ET D’ABAISSEMENT DU Module DE Tête Verrouiller L’INTERRUPTEUR EN Position D’ARRÊTRangement DE LA CLÉ Mise À Niveau DES Rallonges DE TableRangement DE L’OUTIL DE Transfert DU FER Poignée DE TRANSPORT/BARRE DE Transfert DE Matériau Remplacement DES FersPage Lubrification ET Protection Contre LA Rouille Depannage EntretienGarder LA Machine Propre Démarrage ImpossibleLubrification Inspection ET Remplacement DE LA BrosseEntretien ET Réparation AccessoiriesPièces DE Rechange Garantie limitée de deux ans GarantieEspañol Proposición DE California Instrucciones DE Seguridad ImportantesPautas DE SEGURIDAD/DEFINICIONES Normas Generales DE Seguridad Guarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadInstrucciones DE Conexión a Tierra Conexiones a LA Fuente DE AlimentaciónEspecificaciones DEL Motor Prologo Descripción FuncionalContenido DE Carton Cordones DE ExtensiónDE LA Agarradera DE Elevacion Y Descenso EnsamblajeHerramientas DE Ensamblaje Requeridas Estimación DEL Tiempo DE EnsamblajeArrancando Y Deteniendo LA Acepilladora OperaciónEL Deflector DE Virutas Sujecion DE LA Acepilladora a LA Superficie DE ApoyoElevando Y Bajando EL Conjunto DEL Cabezal Fijando EL Interruptor EN LA Posicion DE ApagadoAlmacenamiento DE Llaves Nivelando LAS Mesas DE ExtensionReemplazando LAS Cuchillas Agarradera DE TRANSPORTE/ Barra DE Transferencia DE MaterialPage Falla EN EL Encendido Localizacion DE Fallas MantenimientoMantenga LA Máquina Limpia Lubricacion Inspeccion Y Reemplazo DE CepillosPiezas DE Repuesto ServicioAccesorios GarantiaPlane , Whisper SERIES,WOODWORKER’S Choice