Delta TP305 instruction manual These knobs were removed in Step

Page 13

4.Insert knife transfer tool (G) Fig. 21, underneath center of knife. Lift the knife transfer tool up until knife (H) separates from pins (J) and pull out and remove knife as shown. NOTE: Knife transfer tool is magnetized, allowing it to attach to knife.

5.Rotate knife (H) Fig. 22 end-for-end, or using a new knife, position knife transfer tool (G) on top of knife as shown. Place knife in cutterhead with bevel up underneath locking bar (D), making sure pins (J) in cutterhead engage with holes (K) in knife.

6.Remove knife transfer tool and tighten the six screws at (F) Fig. 23, using wrench (E) supplied.

7.Replace other knife by rotating head 180 degrees and repeat STEPS 3 THROUGH 6.

Fig. 21

 

J

G

H

Fig. 22

 

 

K

 

D

 

J

 

H

 

G

Fig. 23

E

F

F

8.Slide cutterhead guard (B) Fig. 25 in as far as possible and replace two knobs, one of which is shown at

(A) Fig. 25. These knobs were removed in STEP 2.

Fig. 25

A

B

13

Image 13
Contents Contractors Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsStay ALERT, Watch What YOU are Doing General Safety RulesRefer to them often and use them to instruct others Additional Specific Safety RulesMotor Specifications Power ConnectionsGrounding Instructions Functional Description Carton ContentsAssembly Tools Required AssemblyAssembly Time Estimate Raising and Lowering HandleCutterhead Guard OperationFastening Planer to Supporting Surface Starting and Stopping PlanerRaising and Lowering Head Assembly Locking Switch in the OFF PositionKnife Transfer Tool Storage Leveling Extension TablesWrench Storage Carrying HANDLE/STOCK Transfer BAR Replacing KnivesThese knobs were removed in Step Keep Machine Clean Troubleshooting MaintenanceFailure to Start Lubrication & Rust ProtectionLubrication Brush Inspection ReplacementAccessories ServiceWarranty Replacement PartsFrançaise Mesures DE Sécurité Définitions LES Instructions Importantes DE SureteConservez CES Instructions LA Proposition DE CalifornieLutilisation DE CET Outil Règles DE Sécurité GénéralesConserver CES Directives Règles Spécifiques Additionnelles DE SûretéSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Contenus DE Boite Description FonctionnelleAVANT-PROPOS Cordon DE RallongeDésemballage ET Nettoyage AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Abaisser LES Rallonges DE TableDispositif DE Protection DES Fers FonctionnementFixation DE LA Raboteuse SUR UNE Surface DE Support Démarrage ET Arrêt DE LA RaboteuseSoulèvement ET D’ABAISSEMENT DU Module DE Tête Verrouiller L’INTERRUPTEUR EN Position D’ARRÊTRangement DE L’OUTIL DE Transfert DU FER Mise À Niveau DES Rallonges DE TableRangement DE LA CLÉ Poignée DE TRANSPORT/BARRE DE Transfert DE Matériau Remplacement DES FersPage Garder LA Machine Propre Depannage EntretienDémarrage Impossible Lubrification ET Protection Contre LA RouilleLubrification Inspection ET Remplacement DE LA BrossePièces DE Rechange AccessoiriesEntretien ET Réparation Garantie limitée de deux ans GarantieEspañol Pautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesProposición DE California Normas Generales DE Seguridad Guarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadEspecificaciones DEL Motor Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Contenido DE Carton Descripción FuncionalCordones DE Extensión PrologoHerramientas DE Ensamblaje Requeridas EnsamblajeEstimación DEL Tiempo DE Ensamblaje DE LA Agarradera DE Elevacion Y DescensoEL Deflector DE Virutas OperaciónSujecion DE LA Acepilladora a LA Superficie DE Apoyo Arrancando Y Deteniendo LA AcepilladoraElevando Y Bajando EL Conjunto DEL Cabezal Fijando EL Interruptor EN LA Posicion DE ApagadoAlmacenamiento DE Llaves Nivelando LAS Mesas DE ExtensionReemplazando LAS Cuchillas Agarradera DE TRANSPORTE/ Barra DE Transferencia DE MaterialPage Mantenga LA Máquina Limpia Localizacion DE Fallas MantenimientoFalla EN EL Encendido Lubricacion Inspeccion Y Reemplazo DE CepillosAccesorios ServicioGarantia Piezas DE RepuestoPlane , Whisper SERIES,WOODWORKER’S Choice