Mitsubishi Electronics 882.00207.00 specifications Typical Batch Sizes Blender Batch Size lbs

Page 53

Because the blending systems must handle a wide variety of materials with varying bulk densities, the actual amount of weight of material the weigh hopper will hold can vary dramatically from application to application.

This feature allows the operator to change the size of the batch to be made. A value will need to be entered between 0.5 and 99.9. This can also be changed while making a batch without affecting the current running batch. If the size is changed then you will need to touch “Accept New Recipe” on the Recipe screen before the change takes place. This feature allows stored recipes with different batch sizes to easily be loaded without the operator having to reconfigure the blender every time they want to load a stored recipe.

The weigh hopper size selected should be one that approaches the maximum capacity of the load cells without over-filling the weigh hopper. During the initial setup of each blender, the weigh hopper size setting should be checked to ensure that the weigh hopper is not overfilling due to a large percentage of light weight regrind, etc. The batch size will vary from model to model. The bulk density of the material being blended will also affect the batch size.

Note: If running a high percentage of lighter density regrind, set the batch size so that the mixer does not overfill, preventing the weigh hopper from fully dumping when operating in “Batch Ready Mode.”

Figure 38: Typical Batch Sizes

Blender

Batch Size (lbs.)

150

1.5

500

4.0

900

8.0

2500

25.0

4000

35.0

6000

45.0

Inventory Shutdown

In many applications, the user of the Slide Gate/Auger System produces large runs of blended material on the same recipe during production. An example may be a 40,000-lb. run of a certain specification plastic extrusion. Others may wish to fill a 1,000-lb. gaylord box in a central blending application. In either case, the manufacturer has provided a means to automatically stop the blending system when the blended material has reached a preset total blended weight. This is known as Inventory Shutdown.

When the Inventory Shutdown value is reached, the blender will finish the current batch of material. It will then stop and display to the operator that the inventory value has been reached. Additionally, it will flash an alarm and wait for operator attention. An example of this screen is shown below:

Figure 39: Typical Blender Shutdown User Prompt Operator Screen

Touch to make another box of material

Touch if you don’t want to make another batch

882.00207.00

Chapter 4: Operation

52 of 102

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department Event of Shipping Damage Unpacking and InspectionIf the Shipment is Not Complete If the Shipment is Not CorrectCredit Returns Warranty ReturnsReturns Table of Contents Maintenance Customer Responsibilities Technical Specifications Safety Symbols Used in this Manual How to Use This ManualSafety Tags and Warning Labels Description Wear Safety Glasses and Work Gloves Follow all Safety CodesOperator Responsibility ResponsibilityGeneral Responsibility Remember Reporting a Safety Defect Maintenance ResponsibilityCustomer Service AccessoriesModels Covered in This Manual General DescriptionEquipment Specifications Controller Features Typical Features and ComponentsMechanical Features Supply Hoppers System Component DescriptionSlide Gates Weigh Hopper Typical Slide Gate AssemblyTypical Weigh Hopper Assembly Operator Control Panel Display Mix ChamberController Pushbuttons & Touchscreen Tags Button Function Typical Operator Screens Typical Setup Screens 882.00207.00 Functional Description Pneumatic Slide Gate below Mixer Optional ComponentsLow Level Sensors Mezzanine and Floor StandsTake-off Compartments Regrind Auger Metering R.A.M. HopperAdditive Feeder Hopper Safety Circuit Standards Safety FeaturesSafety Device Lock-Outs Fail Safe OperationTwist Cap Plug Connected to Each Feeder Auger Motor Electrical Disconnect PlugElectrical Safety Interlock Switch Located on mixer door Electric Safety Interlock SwitchUncrating the Equipment Mechanical InstallationMachine Mount Mounting ConfigurationsSite Requirements Typical Mezzanine Mounted Batch Blender Mezzanine MountTypical Floor Mount Central Blender Layout Floor Mount Central BlenderPneumatic Connections Electrical ConnectionsStroke Limiters for Metering Gates Initial Set-upMechanical Set-up Weigh Hopper Final Connections Controller Set-up Display Main Recipe ScreenRecipe Page Start Blender Controller Menu StructureBlender Calibration Display Calibration Menu Screen Feeder Calibration Auger Blenders Alarm SetupSetting Date and Time Network SetupAdditional Setup Parameters Initial Startup Start-up Quick Start ProcedureGeneral Operation New RecipesOperator Displays Operation ProceduresExisting Recipes Typical Recipe Entry Operator Screen Recipe Entry Formats Typical Inventory Display Operator ScreenRecipe Format Menu Quickset Mode Most common in injection moldingExample Calculations of a 5-component blend in Quickset mode Recipe Setup Inventory Shutdown Typical Batch Sizes Blender Batch Size lbsMixer and Dump Setup Weigh Hopper Dump Time Re-Mix TimerWeigh Hopper Dump Delay Time Weigh Hopper Dump Cycle Alarm FlagsMixer Dump Time Hopper 1-6 Out of MaterialPower Interruption while metering a Batch Max Hopper Weight Exceeded, Check Batch SizeCalibration Error, Clean out Hopper and Check Calibration Blender Powered On/Off PLC Battery LowInventory Cleared Stop ScreenFeeder Clean Out Recipe Book Diagram in -5 of this manualLoad a Saved Recipe from the Book Display Recipe ContentsSave Running Recipe to the Book Color Changes Erase Recipe or Entire BookTypical Inventory Shutdown Operator Screen Shut-downSample Preventative Maintenance Schedule Preventative Maintenance ScheduleCorrective Maintenance Preventative MaintenanceElectrical Internal Components of the Control PanelOutput Signals from Programmable Controller Input Signals to Programmable ControllerIntroduction TroubleshootingProblem Corrective action Problem Corrective action Controller warranty will be voided Problem Corrective action Warranty Specifications WarrantyWarranty Restrictions Warranty LiabilitiesEquipment Specifications Technical SpecificationsAnnex B Information Final Assembly Drawings and DiagramsMixer Sub-Assembly Typical Mixer Assembly Parts List Typical Hopper Assembly Parts List Hopper Sub-AssemblyTypical R.A.M. Hopper Assembly Parts List Hopper R.A.M. Regrind Auger Metering Sub-Assembly OptionalTypical Additive Feeder Hopper Assembly Parts List Hopper Additive Feeder Sub-Assembly OptionalTypical Weigh Hopper Assembly Parts List Weigh Hopper Sub-AssemblyTypical Slidegate Assembly Parts List Slide Gate Sub-AssemblyTypical Knife Gate below mixer Assembly Parts List Knife Gate Sub-Assembly HD OptionalTypical Knife Gate floor stand Assembly Parts List Knife Gate Sub-Assembly RD OptionalControl Panel Layout Typical Mitsubishi Controller Main Parts ListSpare Parts Kits Blender Spare Parts ListingProgrammable Settings Addendum Service Supervisor InformationPasswords Metering Test Screen Factory Setup MenuAdvanced Weight Options Screen Feed Calibration Options Screen Feed Algorithm Options ScreenMechanical Options Screen Feeder SetupUnits Customer Setup MenuTypical Alarm Flags & Feeder Setup Screen Alarm LogReport Setup Factory Default Setup ParametersLoadcell Calex Module Dipswitch Settings General Blender Info Mitsubishi Communications ManualBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Fixed Decimal Explanation Alarm Number ExplanationRecording the Targets VS. Actuals for Each Batch Technical Assistance Service Department Sales DepartmentParts Department Contract Department882.00207.00 Appendix 102
Related manuals
Manual 103 pages 60.12 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents