Mitsubishi Electronics 882.00207.00 How to Use This Manual, Safety Symbols Used in this Manual

Page 8

Chapter 1: Safety

1-1 How to Use This Manual

Use this manual as a guide and reference for installing, operating, and maintaining your granulator. The purpose is to assist you in applying efficient, proven techniques that enhance equipment productivity.

This manual covers only light corrective maintenance. No other maintenance should be undertaken without first contacting a service engineer.

The Functional Description section outlines models covered, standard features, and safety features. Additional sections within the manual provide instructions for installation, pre- operational procedures, operation, preventive maintenance, and corrective maintenance.

The Installation chapter includes required data for receiving, unpacking, inspecting, and setup of the blender. We can also provide the assistance of a factory-trained technician to help train your operator(s) for a nominal charge. This section includes instructions, checks, and adjustments that should be followed before commencing with operation of the blender. These instructions are intended to supplement standard shop procedures performed at shift, daily, and weekly intervals.

The Operation chapter includes a description of electrical and mechanical controls, in addition to information for operating the blender safely and efficiently.

The Maintenance chapter is intended to serve as a source of detailed assembly and disassembly instructions for those areas of the equipment requiring service. Preventive maintenance sections are included to ensure that your blender provides excellent, long service.

The Troubleshooting chapter serves as a guide for identification of most common problems. Potential problems are listed, along with possible causes and related solutions.

The Appendix contains technical specifications, drawings, schematics, parts lists, and available options. Refer to this section for a listing of spare parts for purchase. Have your serial number and model number ready when ordering.

Safety Symbols Used in this Manual

The following safety alert symbols are used to alert you to potential personal injury hazards. Obey all safety messages that follow these symbols to avoid possible injury or death.

DANGER! DANGER indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury.

WARNING! WARNING indicates a potentially hazardous situation or practice that, if not avoided, could result in death or serious injury.

Caution! CAUTION indicates a potentially hazardous situation or practice that, if not avoided, may result in minor or moderate injury or in property damage.

882.00207.00

Chapter 1: Safety

7 of 102

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Gravimetric Slide Gate Batch Blender Mitsubishi Controller Parts and Service Department Unpacking and Inspection Event of Shipping DamageIf the Shipment is Not Complete If the Shipment is Not CorrectCredit Returns Warranty ReturnsReturns Table of Contents Maintenance Customer Responsibilities Technical Specifications How to Use This Manual Safety Symbols Used in this ManualSafety Tags and Warning Labels Description Follow all Safety Codes Wear Safety Glasses and Work GlovesOperator Responsibility ResponsibilityGeneral Responsibility Remember Maintenance Responsibility Reporting a Safety DefectAccessories Customer ServiceModels Covered in This Manual General DescriptionEquipment Specifications Controller Features Typical Features and ComponentsMechanical Features System Component Description Supply HoppersSlide Gates Typical Slide Gate Assembly Weigh HopperTypical Weigh Hopper Assembly Mix Chamber Operator Control Panel DisplayController Pushbuttons & Touchscreen Tags Button Function Typical Operator Screens Typical Setup Screens 882.00207.00 Functional Description Optional Components Pneumatic Slide Gate below MixerLow Level Sensors Mezzanine and Floor StandsTake-off Compartments Regrind Auger Metering R.A.M. HopperAdditive Feeder Hopper Safety Features Safety Circuit StandardsSafety Device Lock-Outs Fail Safe OperationElectrical Disconnect Plug Twist Cap Plug Connected to Each Feeder Auger MotorElectric Safety Interlock Switch Electrical Safety Interlock Switch Located on mixer doorMechanical Installation Uncrating the EquipmentMachine Mount Mounting ConfigurationsSite Requirements Mezzanine Mount Typical Mezzanine Mounted Batch BlenderFloor Mount Central Blender Typical Floor Mount Central Blender LayoutElectrical Connections Pneumatic ConnectionsStroke Limiters for Metering Gates Initial Set-upMechanical Set-up Weigh Hopper Final Connections Display Main Recipe Screen Controller Set-upBlender Controller Menu Structure Recipe Page StartBlender Calibration Display Calibration Menu Screen Alarm Setup Feeder Calibration Auger BlendersNetwork Setup Setting Date and TimeAdditional Setup Parameters Initial Startup Quick Start Procedure Start-upGeneral Operation New RecipesOperator Displays Operation ProceduresExisting Recipes Typical Recipe Entry Operator Screen Typical Inventory Display Operator Screen Recipe Entry FormatsQuickset Mode Most common in injection molding Recipe Format MenuExample Calculations of a 5-component blend in Quickset mode Recipe Setup Typical Batch Sizes Blender Batch Size lbs Inventory ShutdownMixer and Dump Setup Weigh Hopper Dump Time Re-Mix TimerWeigh Hopper Dump Delay Time Alarm Flags Weigh Hopper Dump CycleMixer Dump Time Hopper 1-6 Out of MaterialPower Interruption while metering a Batch Max Hopper Weight Exceeded, Check Batch SizeCalibration Error, Clean out Hopper and Check Calibration PLC Battery Low Blender Powered On/OffInventory Cleared Stop ScreenFeeder Clean Out Diagram in -5 of this manual Recipe BookLoad a Saved Recipe from the Book Display Recipe ContentsSave Running Recipe to the Book Erase Recipe or Entire Book Color ChangesShut-down Typical Inventory Shutdown Operator ScreenPreventative Maintenance Schedule Sample Preventative Maintenance SchedulePreventative Maintenance Corrective MaintenanceElectrical Internal Components of the Control PanelInput Signals to Programmable Controller Output Signals from Programmable ControllerTroubleshooting IntroductionProblem Corrective action Problem Corrective action Controller warranty will be voided Problem Corrective action Warranty Warranty SpecificationsWarranty Restrictions Warranty LiabilitiesTechnical Specifications Equipment SpecificationsAnnex B Information Drawings and Diagrams Final AssemblyMixer Sub-Assembly Typical Mixer Assembly Parts List Hopper Sub-Assembly Typical Hopper Assembly Parts ListHopper R.A.M. Regrind Auger Metering Sub-Assembly Optional Typical R.A.M. Hopper Assembly Parts ListHopper Additive Feeder Sub-Assembly Optional Typical Additive Feeder Hopper Assembly Parts ListWeigh Hopper Sub-Assembly Typical Weigh Hopper Assembly Parts ListSlide Gate Sub-Assembly Typical Slidegate Assembly Parts ListKnife Gate Sub-Assembly HD Optional Typical Knife Gate below mixer Assembly Parts ListKnife Gate Sub-Assembly RD Optional Typical Knife Gate floor stand Assembly Parts ListTypical Mitsubishi Controller Main Parts List Control Panel LayoutBlender Spare Parts Listing Spare Parts KitsProgrammable Settings Addendum Service Supervisor InformationPasswords Metering Test Screen Factory Setup MenuAdvanced Weight Options Screen Feed Algorithm Options Screen Feed Calibration Options ScreenFeeder Setup Mechanical Options ScreenCustomer Setup Menu UnitsAlarm Log Typical Alarm Flags & Feeder Setup ScreenFactory Default Setup Parameters Report SetupLoadcell Calex Module Dipswitch Settings Mitsubishi Communications Manual General Blender InfoBlender Alarms Inventory Info Recipe Info this is Where YOU Right the NEW Recipe to Recipe Book Manipulation Alarm Number Explanation Fixed Decimal ExplanationRecording the Targets VS. Actuals for Each Batch Service Department Sales Department Technical AssistanceParts Department Contract Department882.00207.00 Appendix 102
Related manuals
Manual 103 pages 60.12 Kb

882.00207.00 specifications

Mitsubishi Electronics has always been at the forefront of innovation in the field of electronics, and one of its significant products is the Mitsubishi Electronics 882.00207.00. This device is designed for enhanced performance and reliability, providing a range of features that cater to both industrial and consumer needs.

One of the main features of the Mitsubishi 882.00207.00 is its robust design, which ensures durability in demanding environments. The device is built to withstand harsh conditions, making it ideal for industrial applications where reliability is critical. Its rugged construction means that it can operate efficiently in extreme temperatures, humidity, and other challenging conditions.

In terms of technology, the Mitsubishi 882.00207.00 incorporates advanced electronic components that enhance its functionality. This includes state-of-the-art processing capabilities that allow for quick data processing and seamless operation. The device’s integration of cutting-edge technology ensures that it meets the performance demands of modern applications while providing energy efficiency.

Another notable characteristic is its user-friendly interface. The device is designed with ease of use in mind, allowing operators to interact with it effortlessly. This ensures that even those with minimal technical expertise can operate the device effectively. The clear display and intuitive controls make it accessible for a wide range of users, facilitating smoother operations in various settings.

The Mitsubishi 882.00207.00 is also equipped with multiple connectivity options. This enables it to integrate seamlessly with other devices and systems, facilitating enhanced communication and data transfer. Whether it’s connecting to existing networks or interfacing with new technologies, the device’s versatility ensures it can adapt to evolving technological landscapes.

Additionally, the device is backed by Mitsubishi's commitment to quality and customer support. Users can expect reliable service and assistance, ensuring that they can maximize the potential of their investment.

In conclusion, the Mitsubishi Electronics 882.00207.00 stands out in the electronics market for its durable construction, advanced technology, user-friendly design, and versatile connectivity options. This makes it an invaluable tool for both industrial applications and everyday consumer use, embodying the innovative spirit that Mitsubishi Electronics is known for.
Top Page Image Contents